AeraMax Professional AM III Manual de instalação - Página 3

Procurar online ou descarregar pdf Manual de instalação para Sistemas de controlo AeraMax Professional AM III. AeraMax Professional AM III 4 páginas. Air quality control system
Também para AeraMax Professional AM III: Manual de início rápido (8 páginas), Manual de instruções (16 páginas)

AeraMax Professional AM III Manual de instalação
MOUNTING REAR HOUSING AND MAIN ASSEMBLY
Test the electrical outlet box first to ensure rated power requirements are met before beginning installation.
Remove air purifier from its shipping carton and remove all packing material.
Fig 3
Fig 4
Place the air purifier face up on a
Open access panel and remove
filter assembly by pulling out on
flat, stable work surface. Open the
access panel by pressing in latches
top of side edges of frame, then
on each side of the unit (Fig 3).
lifting. NOTE: remove all plastic
wrap from filters (Fig 4).
Fig 7
Fig 8
REAR HOUSING INSTALLATION & WIRING
Reference rear housing and locate desired mounting location. Again, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to
an existing stud.
Using provided template ensure electrical
Fig 9
outlet box is located behind cable hole (A)
A
A
in Rear Housing assembly (Fig 9). Drill
holes and place anchors in wall.
If mounting on concrete, cinder block or
B
brick type walls route the wires through
B
the "punch-out" hole marked (B) in Fig 9.
Fig 11
Attach wires from electrical outlet box to wires located inside rear housing using wire nuts. Match up line (black) and neutral (white) wires (Fig 11). Make sure
all connections are made in accordance with federal, state and local codes and regulations.
4
AeraMaxPRO_AMIII_InstallGuide_408530_RevB_111314.indd 4-5
Fig 5
Fig 6
1
2
Remove the four housing screws (Fig 5 & 6) and set aside for re-assembly.
3
4
At the location of the two upper
Disconnect main housing assembly
housing screws (Fig 5), insert a flat
from rear housing assembly.
head screwdriver and gently twist
Separate main housing from rear
to release tab as shown in Fig 7.
housing. Lift main housing assembly
This will disconnect main housing
away from rear mounting housing
assembly from the rear housing
(Fig 8).
assembly.
Check for washers at all mounting
Fig 10
screw locations (Fig 10). Pull wires
from electrical outlet box through
hole in rear housing. Align housing
over anchors and securely install all
mounting screws.
MAIN ASSEMBLY INSTALLATION
WARNING:
To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before continuing any installation work.
1
2
Fig 12
Fig 13
A
A
B
3
4
The power connector (B, in Fig
Carefully align the main assembly
12) will carry power from the rear
with the rear housing assembly.
housing to the main housing once
Slowly press into place until snap
the assemblies are fully seated.
is heard, and there is no gap
The main assembly will attach to
between the assemblies (Fig 13).
the rear housing assembly by the
The unit should now support its
four screws previously removed
own weight.
(Fig 5 & 6). Two snap hooks (A,
in Fig 12) will hold the main and
rear assemblies together until the
screws can be installed.
RE-INSTALLING FILTERS
IMPORTANT:
Make sure all plastic wrap is removed from filters.
Fig 16
Fig 17
Make sure filters are in correct
IMPORTANT: Make sure filter
order - pre-filter / carbon filter /
detection area aligns with window
HEPA filter - and inserted into filter
in filter frame (Fig 17).
frame (Fig 16).
Fig 20
Once the unit is closed re-establish
power. Lights on the control panel
will be visible through the lens,
indicating the unit is operational
(Fig 20). The power light indicator
will flash once a second.
1
2
Fig 14
Fig 15
3
4
1
2
Install four screws (previously removed) to secure main assembly to rear
housing assembly (Fig 14 & 15).
3
4
Fig 18
Fig 19
Open front panel by pressing
Close front panel by pressing
latches on both sides of unit. Allow
firmly until both sides latch closed
door to open fully. Insert filters
(Fig 19).
– IMPORTANT: make sure filter
detection window is aligned in
upper right corner (Fig 18).
LOCKING ACCESS PANEL
To restrict access to the control panel
Fig 21
and filters the unit can be locked. To
lock, insert the key provided and
rotate clockwise ¼ turn (Fig 21).
11/13/14 11:01 AM
5