AeraMax Professional AM III Manual de início rápido - Página 3

Procurar online ou descarregar pdf Manual de início rápido para Sistemas de controlo AeraMax Professional AM III. AeraMax Professional AM III 8 páginas. Air quality control system
Também para AeraMax Professional AM III: Manual de instalação (4 páginas), Manual de instruções (16 páginas)

Imprimir página

AeraMax Professional AM III Manual de início rápido

DISPLAY PANEL

NOTE: after the unit is turned on the "AQ" light will flash for a few minutes while the system self-calibrates.

HEPA FILTER REPLACEMENT INDICATOR –

This indicator will show

its status when the access panel is open or closed. If the light is red this indicates

the filter needs replacing. The replacement period will vary depending on the

filters used, hours of use, air quality, and rate of air flow. For filter replacement

indicator descriptions see FILTER REPLACEMENT INDICATORS section.

CARBON FILTER REPLACEMENT INDICATOR –

This indicator will

show its status when the access panel is open or closed. If the light is red this

indicates the filter needs replacing. The replacement period will vary depending

on the filters used, hours of use, air quality, and rate of air flow. For filter

replacement indicator descriptions see FILTER REPLACEMENT INDICATORS section.

ACCESSORY INDICATOR –

This indicator will show its status when the

access panel is open or closed. This indicator will only be used if an accessory filter

is installed in the unit. If the light is red this indicates the filter needs replacing.

The replacement period will vary depending on the filters used, hours of use, air

quality, and rate of air flow. For filter replacement indicator descriptions see FILTER

REPLACEMENT INDICATORS section.

AIR QUALITY SENSOR –

This indicator will show its status when the

access panel is open or closed. This indicator monitors the air quality and adjusts

the fan speed to keep your air purified. Blue, amber, and red lights indicate the

purity of your air.

PlasmaTRUE™ TECHNOLOGY –

This indicator will show its status when

the access panel is open or closed. Creates an ionized field to help safely remove

airborne pollutants. To turn on and off the PlasmaTRUE™ TECHNOLOGY, touch

and hold the PLASMA indicator. A blue light illuminates when the PlasmaTRUE™

TECHNOLOGY is enabled. To disable the PlasmaTRUE™ TECHNOLOGY, press and

hold "Plasma" indicator until light is off.

OPERATION

The air purifier continuously works in automatic mode; the user can select which preference they would like the purifier to use based on the location or desired

operation of the air purifier. The purifier will operate through a minimized range of speeds, not exceeding the maximum level selected, in order to run quietly while

cleaning the room of contaminants. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption and

extend the life of the filters.

When Normal mode is selected the Normal indicator on the control panel will be blue when the access panel is open. The purifier will operate through its full range

of speeds in order to clean the room of contaminates as quickly as possible. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode

to reduce energy consumption and extend the life of the filters.

When Quiet mode is selected the Quiet indicator on the control panel will be blue when the access panel is open. The purifier will operate through a minimized range

of speeds in order to stay as quiet as possible while cleaning the room of contaminates. Once air is cleaned, and no sensors are activated, the unit lowers to energy

saving mode to reduce energy consumption and extend the life of the filters.

NORMAL MODE –

Select this mode for restrooms, cafeterias, fitness areas,

and other louder areas as rapid purification is initiated when the room is occupied

and/or strong airborne contaminants are present. To select, press and hold the

"Normal" indicator until icon illuminates. This mode monitors air quality, motion, and

noise level to adjust the fan speed in order to keep your air purified as quickly as

possible. The fan can reach turbo speed to clean the room in the case of high levels

of contaminant.

QUIET MODE –

This mode utilizes the 3 lowest, most quiet of the 5 fan speeds.

Select this mode for classrooms, meeting rooms, offices, and other quieter areas as

the unit will not run faster than the maximum set speed. To select, press and hold

the "Quiet" indicator until icon illuminates. Continue to press and hold the indicator

to switch between the maximum speeds in this mode. There are three different

levels; each level represents a maximum fan speed that the unit can achieve.

• Level 1 = The lowest speed, the unit will beep one time when this mode

has been selected and the unit will not run faster than this lowest speed.

• Level 2 = Low speed, the unit will beep two times when this mode has

been selected and the unit will not run faster than low speed.

• Level 3 = Medium speed, the unit will beep three times when this mode has been

selected and the unit will not run faster than medium speed.

The Quiet Mode monitors air quality, motion, and noise level to adjust the fan speed

in order to keep the air purified as efficiently as possible while not exceeding the

maximum speed level selected.

CARE AND MAINTENANCE

CLEANING:

• Clean external housing as necessary by wiping with a dry, soft cloth; for stains, use a warm, damp cloth.

• Do not use volatile fluids such as benzene, paint thinner, scouring powder or other cleaners that may damage the unit surface.

• Clean intake and exhaust vents by wiping with a dry, soft cloth.

FILTER REPLACEMENT INDICATORS:

The replacement filter indicators will signal when to replace the HEPA Filter and/or Carbon with Pre-Filter. The replacement period will vary depending on the

hours of use, air quality, and rate of air flow. However, under normal usage, most HEPA Filters need to be replaced every 2 years, and Carbon with Pre-Filter

every 6 months. When a filter needs to be replaced the following color will be shown on any one of the HEPA, CARBON, or ACCESSORY filter replacement

indicators:

Red flashing = 90% filter wear (recommendation to order new filters)

Red steady = 100% filter wear (replace with new filters)

Do not wash and reuse any of the filters – they will not work effectively. Only use AeraMax ® PRO brand replacement filters as units will not function using

any other replacements.

FILTER REPLACEMENT PROCEDURE:

Unlock access panel: to unlock, insert

Open front access panel by pressing

the key provided and rotate counter-

latches on both sides of unit. Allow

clockwise ¼ turn.

panel to open fully. Remove filter(s)

to be replaced.

FILTER REPLACEMENT:

When installing a new filter the unit will automatically detect the filter type but the user will have to manually reset the filter replacement indicators.

To reset any of the filter replacement indicators use the following procedure:

Touch and hold the illuminated

Release finger from indicator.

indicator for three seconds

until a beep is heard and the

indicator is flashing green.

Note: If you do not complete step three within 10 seconds of completing step 1 then the indicator light will not be reset.

TROUBLESHOOTING

PROBLEM:

POSSIBLE SOLUTION:

The air quality control system fails to start.

• Check to assure unit is connected to power supply.

• Make sure filters are genuine AeraMax

brands. IMPORTANT: Make sure filter detection area on genuine AeraMax

replacement filter aligns with window in filter frame.

• Review "Re-Installing Filters" section for further detail.

• Make sure front access panel is closed completely.

• Make sure power switch is on.

The unit makes a faint ticking sound.

• This indicates that the "PlasmaTRUE™" bipolar ionizer is working.

The HEPA and/or Carbon Filter replacement indicator light

• Repeat filter light reset instruction.

remain lit after replacing the filter(s).

Remove any packaging wrap from the

new filters(s) and re-install the filters.

Touch and hold the indicator for

three seconds until a beep is heard

and the indicator light turns off.

PRO filters, as unit will not function with other

PRO