Clarion 2/1 Channel Power Amplifier DPX1000.2 Manual - Página 4
Procurar online ou descarregar pdf Manual para Amplificador Clarion 2/1 Channel Power Amplifier DPX1000.2. Clarion 2/1 Channel Power Amplifier DPX1000.2 8 páginas. Digital 2/1 channel power system amplifier
Também para Clarion 2/1 Channel Power Amplifier DPX1000.2: Manual de operação e instalação (16 páginas)
Imprimir página
degrees Celsius the amplifier will turn off. Once the amplifier cools down, simply reset the amplifier
by its Remote connection, turn the amplifier off and then on again once you have given the amplifier
a chance to cool down and the amp will once again begin to play. Speaker Short Circuit Protection
Should your speakers short circuit due to voice coil burn out, or should the amplifier sense an
impedance too low to handle, the Protection LED will light, indicating a diagnostic condition. T urn
off your system, disconnect one speaker at a time and try to determine which speaker might be
faulty. Correct the condition and restart the amplifier. Y ou must reset the amplifier by turning off
and then on by the Remote power for proper operation after correcting a diagnostic condition. Input
Overload Protection This circuit will either shutdown the amplifier completely or make the amplifier
spurt on and off indicating that it is in a diagnostic condition. T urn the system off and reduce the
gain on the amplifier or volume from your head unit, this should result in a corrected condition. DC
Offset Protection Should any DC voltage try to enter the amplifier via the speaker terminals it will
cause the amplifier to shut down and not operate until this condition is remedied. This circuit will
also protect damaging high DC voltages from reaching your speakers should your amplifier ever
missfunction. This switch enables you to slave multiple RS amplifiers off one master.
Input signal will be connected to the master in a system, and then a PM2 bridging cable can be used
to connect the master out to the slave in of a second amplifier, and in multiple amplifier systems,
this amplifier 's master output can be connected to a third amplifier's slave input, thus allowing the
daisy chaining of an almost unlimited number of amplifiers from one signal source. In addition, a
single Competition Podium Remote control CPR can optionally be connected to the master amplifier,
in order to control all the slave amplifiers connected to it. Note that when an amplifier is set in the
SLA VE mode, its level control, phase shift, subsonic filter, bass EQ, low pass filter, as well as
remote control function will be totally bypassed, as these functions will be controlled by the master
amplifier to ensure perfect level and spectral matching between all amplifiers. Boom ! Harder
Cadence amplifiers operate on 12volt negative ground systems only. It is recommend that you layout
your sound system design on paper first. This will help you during the installation so that you will
have a wiring flow chart and not misswire any of your components. Mount the amplifier in the trunk
or hatch area of your vehicle. Never install an amplifier in the engine compartment or on the
firewall. Please be sure to leave breathing room around the amplifier heatsink so that it can
dissipate the heat it produces ef ficiently. The amplifier can be installed either horizontally or
vertically. When mounting the amplifier on the trunk floor, be sure to watch for your gas tank, gas
lines and electrical lines. Do not drill or mount any screws where they might penetrate the gas tank
of your car. The remote turn on connection is located on the barrier strip next to the power and
ground connections. This connection is responsible for turning the amplifier on and off with the rest
of the system. A smaller gauge wire can be used to make this connection to your radios power
antenna lead.
Should your system not have any turn on leads, you can wire the remote terminal to an accessory
lead, which turns on, with your ignition. The benefits of this feature have been described earlier in
the Features section. Use the heaviest gauge wire available for this connection. We recommend
using Cadence Extreme Series Power Capacitors due to their industry leading low ESR rating.
Multiple capacitors can be connected via BUS BAR terminals for larger amplifier installations. Use a
CAP1DR per amplifier model ZRS8, a CAP2DR per amplifier model ZRS9, and a CAP5DR for
amplifier model ZRS10. The RS amplifiers are of course meant for sub bass applications, and as such
need to be used in conjunction with a second amplifier for a complete full range system. Refer to the
wiring diagram on Page 6. Connect the Line Out of the RS amplifier to the Line Input of a
multichannel amplifier. Set the multichannel amplifier 's internal crossover to High Pass, as it will
drive the high frequency speakers, such as separates, coaxials, or plate type speakers, typically
mounted in the doors or kick panels. Add up the current draw for all amplifiers in the system to
determine the rating for this fuse. Connect the remote turn on signal from the source to all amplifier