Yamaha CP50 Lista de dados - Página 32

Procurar online ou descarregar pdf Lista de dados para Instrumento musical Yamaha CP50. Yamaha CP50 42 páginas. Cp series
Também para Yamaha CP50: Brochura e especificações (16 páginas)

Imprimir página

+--[SW2]-----------SYSTEM REALTIME MESSAGE

TIMING CLOCK

+------------------SYSTEM REALTIME MESSAGE

START

CONTINUE

STOP

+------------------ACTIVE SENSING

+--[SW3]-+---------SYSTEM EXCLUSIVE MESSAGE (All in Seq)

+----------<BULK DUMP>

F0H 43H 0nH 7FH mmH bhH blH ahH amH alH ddH....ddH ccH F7H

mm = CP5: 10, CP50: 11

+----------<PARAMETER CHANGE>

F0H 43H 1nH 7FH mmH ahH amH alH ddH.....ddH F7H

+----------<BULK DUMP REQUEST>

F0H 43H 2nH 7FH mmH ahH amH alH ddH.....ddH F7H

+----------<PARAMETER REQUEST>

F0H 43H 3nH 7FH mmH ahH amH alH F7H

+-------------------SYSTEM EXCLUSIVE MESSAGE

IDENTITY REQUEST

+-------------------SYSTEM EXCLUSIVE MESSAGE

TEST ENTRY

[SW2]

Complies with SYSTEM MIDI Sync setting. (This parameter can be received when it is not set to internal.)

[SW3]

MIDI Device Number

[SW4]

SYSTEM Bank Select Switch

[SW5]

SYSTEM Program Change Switch

[SW6]

MIDI Receive Channel and Receive Filter Complies with Receive Channel and Receive Switch.

(3) TRANSMIT/RECEIVE DATA

(3-1) CHANNEL VOICE MESSAGES

(3-1-1) NOTE OFF

STATUS

1000nnnn (8nH)

NOTE No.

0kkkkkkk

VELOCITY

0vvvvvvv

Receive only

(3-1-2) NOTE ON/OFF

STATUS

1001nnnn (9nH)

NOTE NUMBER

0kkkkkkk

VELOCITY NOTE ON

0vvvvvvv (v≠0)

NOTE OFF

0vvvvvvv (v=0)

(3-1-3) CONTROL CHANGE

STATUS

1011nnnn (BnH)

CONTROL NUMBER

0ccccccc

CONTROL VALUE

0vvvvvvv

*TRANSMITTED CONTROL NUMBER

c =

BANK SEL MSB

c = 32

BANK SEL LSB

c = 64

SUSTAIN SWITCH

c = 0...95

ASSIGNABLE CONTROLLERS

The Sequencer Part will play back all recorded control change messages.

*RECEIVED CONTROL NUMBER

c =

BANK SEL MSB

c = 32

BANK SEL LSB

c =

MODULATION

c =

PORTAMENTO TIME

c =

DATA ENTRY MSB

c = 38

DATA ENTRY LSB

c =

MAIN VOLUME

c = 10

PAN

c = 11

EXPRESSION

c = 31

EG SUSTAIN LEVEL

c = 64

SUSTAIN SWITCH

c = 65

PORTAMENTO SWITCH

c = 66

SOSTENUTO

c = 71

HARMONIC CONTENT

c = 72

EG RELEASE TIME

c = 73

EG ATTACK TIME

c = 74

BRIGHTNESS

c = 75

EG DECAY TIME

c = 91

EFFECT1 DEPTH

c = 93

EFFECT3 DEPTH

c = 96

DATA ENTRY INC

c = 97

DATA ENTRY DEC

c = 0..95

ASSIGNABLE CONTROLLER

All Control Change events can be recorded to the sequence data.

*1 Used only when a value is set using RPN.

*2 Invalid with Drum Voices.

*3 Relation between BANK CHANGE and PROGRAM is as follows:

CATEGORY

Performance Preset 1

Preset 2

Preset 3

User 1

User 2

User 3

External 1

External 2

External 3

F8H

FAH

FBH

FCH

FEH

F0H 7EH 0nH 06H 01H F7H

F0H 43H 73H 01H 60H 00H F7H

n = 0 - 15 CHANNEL NUMBER

k = 0 (C-2) - 127 (G8)

v: ignored

n = 0 - 15 CHANNEL NUMBER

k = 0 (C-2) - 127 (G8)

n = 0 - 15 CHANNEL NUMBER

; v = 0 - 127

; v = 0, 127

; v = 0 - 127

; v = 0: -64 - 64: 0 - 127: +63

; v = 0 - 63: OFF, 64 - 127: ON

; v = 0: -64 - 64: 0 - 127: +63

; v = 0 - 127

; v = 127

; v = 0 - 127

MSB

LSB

PROGRAM No.

0...39 (1...40)

*4 The default CONTROL NUMBERS of ASSIGNABLE CONTROLLER are as follows:

FOOT CONTROLLER 1

FOOT CONTROLLER 2

FOOT SWITCH

PORTAMENTO TIME is set the time it takes for the pitch to reach the next note played when

PORTAMENT SWITCH is set to on.

0: shortest time; 127: longest time

PAN position relatively changes according to the value for each performance part.

EFFECT1 DEPTH controls reverb send level.

HARMONIC CONTENT adjusts the resonance preset for each performance.

Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter.

The larger the value more resonant sound will be produced.

The effective range may be narrower than the range you can designate depending on the selected voice.

The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the

envelopes preset for each performance.

Setting these values add to or subtract from the center value, 64, since these are offset parameters.

BRIGHTNESS adjusts the cutoff frequency preset for each performance.

Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter.

The smaller the value the cutoff frequency will be lowered.

The effective range may be narrower than the range you can designate depending on the selected voice.

Bank Select will be actually executed when the Program Change message is received.

Bank Select and Program Change numbers that are not supported by Yamaha will be ignored.

(3-1-4) PROGRAM CHANGE

STATUS

PROGRAM NUMBER

(3-1-5) CHANNEL AFTER TOUCH

STATUS

VALUE

(3-1-6) PITCH BEND CHANGE

STATUS

LSB

MSB

Transmitted with a resolution of 7 bits.

(3-2) CHANNEL MODE MESSAGES

STATUS

CONTROL NUMBER

CONTROL VALUE

(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)

All the sounds currently played including the channel messages such as note-on and hold-on in a certain channel

are muted when receiving this message.

(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)

Resets the values set for the following controllers.

PITCH BEND CHANGE

MODULATION

EXPRESSION

FOOT CONTROLLER

SUSTAIN SWITCH

SOSTENUTO SWITCH

RPN

Doesn't reset the following data:

PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL,

RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT SEND LEVEL 1, EFFECT SEND

LEVEL 3,PORTAMENTO SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING

(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)

All the notes currently set to on in certain channel(s) are muted when receiving this message.

However, if Sustain or Sostenuto is on, notes will continue sounding until these are turned off.

(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)

Performs the same function as when receiving ALL SOUND OFF.

Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1.

(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)

Performs the same function as when receiving ALL SOUND OFF.

Sets VOICE RECEIVE CHANNEL to "OMNI ON."

(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0)

Sets Part Mode to "mono."

(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)

Sets Part Mode to "poly."

(3-3) REGISTERED PARAMETER NUMBER

STATUS

1011nnnn (BnH)

LSB

01100100 (64H)

RPN LSB

0ppppppp

MSB

01100101 (65H)

RPN MSB

0qqqqqqq

DATA ENTRY MSB

00000110 (06H)

DATA VALUE

0mmmmmmm

DATA ENTRY LSB

00100110 (26H)

DATA VALUE

0lllllll

First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.

RPN

D.ENTRY

LSB MSB MSB LSB

PARAMETER NAME

00H 00H mmH ---

PITCH BEND SENSITIVITY

01H 00H mmH llH

MASTER FINE TUNE

02H 00H mmH ---

MASTER COARSE TUNE

7FH 7FH --- ---

RPN RESET

RPN numbers will be left not designated.

The internal values are not affected.

MIDI Data Format

1100nnnn (CnH)

n = 0 - 15 CHANNEL NUMBER

0ppppppp

p = 0 - 127

1101nnnn (DnH)

n = 0 - 15 CHANNEL NUMBER

0vvvvvvv

v = 0 - 127 AFTER TOUCH VALUE

1110nnnn (EnH)

n = 0 - 15 CHANNEL NUMBER

0vvvvvvv

PITCH BEND CHANGE LSB

0vvvvvvv

PITCH BEND CHANGE MSB

1011nnnn (BnH)

n = 0 - 15 CHANNEL NUMBER

0ccccccc

c = CONTROL NUMBER

0vvvvvvv

v = DATA VALUE

0 (center)

0 (minimum)

127 (maximum)

0 (off)

Not assigned; No change

n = 0 - 15 CHANNEL NUMBER

p = RPN LSB

(Refer to the table as shown below.)

q = RPN MSB

(Refer to the table as shown below.)

m = Data Value

l = Data Value

DATA RANGE

00H - 0CH (0 - 12 semitones)

{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

28H - 40H - 58H (-24 - 0 - +24 semitones)

CP5 / CP50 Data List