Yamaha Stagepas 300 Manual do Proprietário - Página 2

Procurar online ou descarregar pdf Manual do Proprietário para Teclado eletrónico Yamaha Stagepas 300. Yamaha Stagepas 300 2 páginas. Portable pa system stagepas 300
Também para Yamaha Stagepas 300: Manual do Proprietário (2 páginas), Manual do Proprietário (2 páginas)

Imprimir página

Yamaha Stagepas 300 Manual do Proprietário

Quick Guide

Getting sound out of the system

Using the included speakers, set up the system and try it out.

Connect the included speakers and your instruments to

the mixer.

Connect the included speakers to the SPEAKER L/R jack. Connect the sources

(guitar, other instruments) to the input jacks. For details, see "Connection

Example."

Before connecting any devices, make sure to turn off the power for all devices (including microphones or the

included speakers). To avoid any possible malfunction, use only the speaker cables included with the device.

Caution

Also, before turning the power on or off, set the volume levels on all devices to minimum.

NOTE:

For best results when connecting a electric guitar or bass guitar to the mixer, use a direct box, preamp (guitar

amp), or amp simulator.

Set the mixer' s LEVEL controls and MASTER LEVEL control

to the minimum (zero).

This position

Depending on the device used, set the MIC/LINE switch

to MIC (

) or LINE (

) as appropriate.

For low-level signals (such as that of microphones), set the switch to the MIC (

position. For high-level signals (such as keyboard instruments and audio equipment),

set the switch to the LINE (

) position.

Controls and Functions

AC IN jack

Connect the included power cable here.

Be sure to use the included power cord. Use of other cords

may result in malfunction, heat generation, or fire.

Caution

POWER switch

For turning the power to the mixer on and off.

LEVEL meter

The LEVEL meter shows the level of the output signal from the SPEAKER L/R jacks.

If the LIMITER flashes continuously, the internal power amplifier section is being excessively

overloaded and may malfunction. Reduce the output level with the MASTER LEVEL control so

Caution

that the indicator flashes only briefly on the highest transient peaks.

POWER indicator

This lights when the POWER switch is ON. When the indicator flashes, the protection

circuit is operating. Check that the speaker cable is correctly connected to the mixer and

reapply the power.

MONITOR OUT Control

Determines the signal level output from the MONITOR OUT jack.

NOTE: The MASTER LEVEL Control does not affect the signal via the MONITOR OUT Control.

SPEECH/MUSIC switch

Set this switch to SPEECH (

) to optimize the mixer settings and sound quality for

speech purposes and announcements. Set this to MUSIC (

) to optimize the mixer

for musical performance. The switch lights up in yellow when it is set to MUSIC (

Turning the power on

First, turn on the power to any connected devices, then turn

the STAGEPAS 300 power on. If you've connected powered

speakers to the mixer, turn on the power of the mixer ﬁrst,

then the powered speakers.

To avoid any loud, unexpected noise from the speakers, first turn on the

power to those connected devices that are closest to the sound source.

Caution

Example: Sound source (CD player or instrument) → STAGEPAS 300 → (Power amplifier)

When turning off the power to the system, reverse the order described above.

Set the MASTER LEVEL control to the optimum position

(indicated by the arrow).

This position

While playing your instrument or singing into the microphone,

adjust the LEVEL control of the corresponding channel.

Adjust the LEVEL Control of the corresponding channel so that the "0" LED lights up

momentarily.

)

SPEAKER L/R jacks (for included speakers only)

These output the mixed signal channels from 1 to 7/8, and the level is adjusted with the MASTER

LEVEL control. When connecting the included speakers, make sure to turn the power off first.

Also, to avoid any possible malfunction, use only the included speakers and the speaker cables

included with the device.

REC OUT L/R jacks

These output the mixed signal channels from 1 to 7/8, and the level is unaffected by the MASTER

LEVEL control. You can use these jacks, for example, to connect to an external recorder.

MONITOR OUT L (MONO) /R jacks

These output the mixed signal channels from 1 to 7/8, and the level is adjusted with the

MONITOR OUT control. These jacks are convenient for connecting an external powered speaker

for monitoring purposes.

LEVEL control

Use these controls to adjust the volume balance among the various channels.

To reduce noise, set any LEVEL controls on unused channels to the minimum.

Caution

MASTER LEVEL Control

Determines the volume of the signal output from the SPEAKER L/R jacks. This allows

you to adjust the overall volume without changing the relative volume balance among

the various channels (made with the LEVEL controls) or the tone settings (made with

the Equalizer).

Use the MASTER LEVEL control to adjust the overall volume.

If the LIMITER indicator flashes continuously, the internal power amplifier section is being

excessively overloaded and may malfunction.

Caution

Applying reverb or echo to the sound

Reverb recreates the warm ambience of an actual performance space, such as a concert hall

or a night club.

For each channel you want to apply reverb, set the

corresponding REVERB switch to ON (

Use the REVERB control to adjust the overall reverb.

Channel input jacks (CH 1 to 4)

For connecting a guitar, microphone, keyboard or other instrument/device. For low-level signals (such as

that of microphones), set the MIC/LINE switch to the MIC (

) position. For high-level signals (such as

keyboard instruments and audio equipment), set the MIC/LINE switch to the LINE (

) position.

NOTE: On any given channel, you may use either XLR or phone jack, but not both. Please connect to

only one of these jacks on each channel.

Stereo channel input jacks (CH 5/6, 7/8)

Input the left and right channels of a stereo signal into the respective odd and even channels of

the mixer.These inputs are intended mainly for use with instruments and equipment having stereo

outputs, such as a synthesizer or CD player.

NOTE: The channel 5/6 input provides two sets of jacks—both phone jacks and RCA-pin jacks. Either one one of these

jacks may be used, but not both at the same time. Please connect to only one of these jacks on each channel.

MIC/LINE switch

Set this switch to MIC or LINE for channels 1 to 4, depending on the level of the input signal. For low-level

signals (such as that of microphones), set the switch to the MIC (

) position. For high-level signals

(such as keyboard instruments and audio equipment), set the switch to the LINE (

) position.

Equalizer

HIGH Determines the level of the high frequency band for each channel. Rotating the knob

clockwise boosts the high frequencies and produces a clearer, crisper sound. If you start

getting feedback (a high-pitched squealing sound) or you want to make the sound softer and

less harsh, turn the knob counterclockwise slightly.

L O W Determines the level of the low frequency band for each channel. Rotating the knob clockwise

boosts the low frequencies and produces a deeper, warmer sound. If you start getting

feedback or you want to make the sound less boomy, turn the knob counterclockwise slightly.

REVERB switch

Set this switch to ON to recreate the rich ambience of various performance environments, such

as a concert hall or a night club. The switch lights up in green when REVERB is ON (

REVERB control

Determines the overall level of the reverb or echo that is applied to the

output signal. For best results, this level should not be set very high, to

avoid possible feedback and to prevent the sound from becoming

"muddy" with too much reverb.

Connection Example

The STAGEPAS 300 can be used in a wide variety of sound reinforcement applications,

from a full-band performance onstage to solo street performance—providing a

powerful, high-performance system in an exceptionally compact and portable package.

Connect a guitar or a microphone to the monaural input jacks (channels 1 to 4) and

connect a keyboard to the stereo input jacks (channels 5/6 or 7/8). If you have a

powered speaker, you can connect it to the MONITOR OUT jack for monitoring your

vocals. For optimum results in band performance applications and to create a more

powerful sound for music, make sure to set the SPEECH/MUSIC switch to MUSIC.

NOTE:

For best results when connecting a electric guitar or bass guitar to the mixer, use a direct box,

preamp (guitar amp), or amp simulator.

Included Speakers

Guitar

Microphones

Powered SP

Microphones

The STAGEPAS 300 features a convenient storage

compartment in the speaker box for packing the included

power cable, speaker cable, Owner' s Manual (this booklet),

and an optional microphone, as shown above. Remove

the rear panel of the speaker and put in the things you

need. Carry the STAGEPAS 300 with you, and you've got

all you need to set up and perform—anywhere, anytime.

Keyboard, etc.

PAN/SEND

PAN

ASSIGN A

ASSIGN B

REVERB

CHORUS

ASSIGN 1

ASSIGN 2

TEMPO

REMOTE

R-AUDIO

ARPEGGIO

KNOB

TONE

ASSIGN

CUTOFF

SWING

GATE TIME

RESONANCE

VELOCITY

ATTACK

UNITMULTIPLY

RELEASE

ON/OFF

G-MIDI

ON/OFF

PRE 1

PRE 2

PRE 3

PRE 4

Integrated Sampling Sequencer / Modular Synthesis Plug-in System / Real-time External Control Surface

MUSIC PRODUCTION SYNTHESIZER

CONTROL

FUNCTION

ARP FX

EFFECT

BYPASS

MASTER

MODE

SLOT