Yamaha YHT-270 Manual de ligação do sistema

Procurar online ou descarregar pdf Manual de ligação do sistema para Teclado eletrónico Yamaha YHT-270. Yamaha YHT-270 1 páginas. Digital home theater system
Também para Yamaha YHT-270: Especificação (2 páginas)

Imprimir página

Printed in China

YHT -270

DIGITAL HOME THEATER SYSTEM

SYSTEM CONNECTION GUIDE

Thank you for selecting this YAMAHA YHT-270.

About This system

Front speakers (NX-E270) 1

Center speaker (NX-C270) 2

Subwoofer (SW-P270) 4

Surround speakers (NX-E270) 3

Receiver (HTR-5930)

Supplied accessories

For NS-E270 / NS-C270

For SW-P270

For HTR-5930

Speaker cable

AM loop antenna

Subwoofer cable

4 m (157-1/2") x 3

10 m (393-11/16") x 2

4 m (157-1/2") x 1

for Center/Front

for Surround

speakers

Indoor FM antenna

Remote control, Batteries (AA,

Non-skid pad

R06, UM-3) x 2 and Owner's

Fastener x 2 set

4 pcs x 1 set

manual are also included, but

8 pcs x 2 set

for NS-C270

For NS-E270

not shown.

Major specifications for speakers

(HTR-5930: refer to the "HTR-5930 Owner's manual" for specifications and safety cautions.)

NX-E270

NX-C270

SW-P270

acoustic-suspension

Advanced YAMAHA

Type

speaker system,

Active Servo Technology,

Magnetically shielded type

Power

Maximum: 80 W

Maximum: 100 W

Dynamic power: 100 W

Frequency response

100 Hz - 25 kHz

130 Hz - 20 kHz

30 Hz - 200 Hz

105 x 151 x 113 mm

300 x 72 x 113 mm

200 x 365 x 370 mm

Dimension

(W x H x D)

(4-1/8" x 5-15/16" x 4-7/16")

(11-13/16" x 2-27/32" x 4-7/16")

(7-7/8" x 14-3/8" x 14-9/16")

0.9 kg (1.98 lbs)

8.5 kg (18.74 lbs)

Weight

0.8 kg (1.76 lbs)

About speakers

Before making connections, place all speakers in their respective positions. The positioning of the

speakers is important because it controls the whole sound quality of your audio system.

Place the speakers depending on your listening position by following the instructions below.

Carrying most of the music/sound effects.

Front speakers

Place them on both sides of your TV set. Approximately at the same height as the TV set.

Emitting center sound such as dialog.

Place it precisely between the front speakers. You can place the center speaker on top of the TV if the top

Center speaker

is flat, on the floor under the TV, or inside the TV rack. Be sure to place the speaker in a stable position.

Providing the surround/ambient effects.

Surround speakers

Place them behind your listening position, facing slightly inward. About 1.8 m (approx. 6 feet) from the

floor.

Adding the low-frequency bass sound.

Subwoofer

As a recommended positioning of the subwoofer, place the subwoofer on the outside of either the right or

the left front speaker. For more detail, read "3 Placing the speakers - Subwoofer".

Speaker layout

Front R

Subwoofer

Front L

Surround R

Center

Surround L

WG84200

Placing the speakers

Center speaker

When placing the speaker on top of the TV rack, etc., attach

the provided fasteners at two points on the bottom of the

speaker and on the top of the TV.

Peel off

the seal

Notes

• Do not place the center speaker on top of a TV whose area is

smaller than the bottom of the speaker. If placed, the speaker

may fall and cause injury.

• Do not place the center speaker on top of a TV if the top is

inclined.

• Do not touch the adhesive surface after peeling off the seal, as

this will waken its adhesive strength.

• Thoroughly wipe clean the surface where the fastener is to be

applied. Note that adhesive strength is weakened if the surface is

dirty, oily or wet and that this may cause the center speaker to

fall.

Front and surround speakers

Placing the speakers

When placing the speakers on a flat surface,

attach the included non-skid pads to the corner on

the bottom of the speakers. This prevents the

speakers from sliding.

Mounting the speakers on the wall

You can mount the front and/or surround speakers on a wall. To mount them on a wall, use the holes of the

brackets attached on the back panels of the speakers.

Fasten two screws into a firm wall or wall support at

Hang the speaker by mounting the holes on the

protruding screws.

the interval shown below.

Make sure that the screws are securely affixed by the

narrow parts of the holes.

70 mm

(2-3/4")

70 mm

Holes

(2-3/4")

70 mm

(2-3/4")

10 mm

(2-3/4")

Minimum

20 mm (25/32")

Caution

• Each speaker weighs 0.8 kg (1.76 lbs).

• Do not mount the speakers on thin plywood or a wall composed of a soft surface material. If mounted, the

screws may pull out of the flimsy surface and the speakers may fall. This may damage the speakers or cause

personal injury.

• Do not affix the speakers to a wall using nails, adhesives, or any other unstable hardware. Long-term use and

vibrations may cause the speakers to fall.

• To avoid accidents resulting from tripping over loose speaker cables, fix the cables to the wall.

• Select an appropriate position on the wall to mount the speaker so that no one will injure his/her head or face.

Installing the speakers on commercially available speaker stands

When you install the speakers on commercially

*Please use the speaker stand that fits with this size.

available speaker stands, you need to attach the

brackets (option) to the bottom of the speakers using

screws (option).

60 mm (2-3/8")

Subwoofer

It is recommended to place the subwoofer on the outside

Use the non-skid pads

of either the right or the left front speaker (figure A). The

placement shown in figure B is also possible, however, if

Attach the provided non-skid pads at the four corners on

the subwoofer is placed directly facing the wall, the bass

the bottom of the subwoofer to prevent the subwoofer

sound may lessen because the sound from the subwoofer

from moving by vibrations, etc.

and the sound reflected by the wall may cancel out each

other. To prevent this from happening, face the subwoofer

obliquely to the wall.

: Subwoofer

: Front speaker

Connecting speakers and antennas to the receiver

CAUTION

Plug the power cables for the AV receiver

and other audio/video components into an

AC outlet only after you complete all other

connections.

Keep the speaker cables as short as

possible. Do not bundle or roll up excess

cable. If the connections are faulty, you will

hear no sound from the speakers.

Before connecting

• Cut the supplied speaker cable to the appropriate

length as required.

• Remove the insulation coating at extremity of each

speaker cable by twisting the coating off.

Notes

• Do not let uninsulated bare wires touch each other as this

could damage the speaker or the amplifier.

• Securely twist the bare wires and lump them together to

prevent them causing a short circuit.

Good

Not Good

10 mm

(3/8")

Non-skid pad

4 4 4 4 4

Connecting other components to the receiver

This procedure introduces an example of digital and

analog connections. For information about other

connection methods, refer to the "HTR-5930

Owner's Manual".

CAUTION

Plug the power cables for the AV receiver

and other audio/video components into an

AC outlet only after you complete all other

connections.

Information on jacks

and cable plugs

Audio jacks and cable plugs

Insert only M4

screws through the

AUDIO

DIGITAL AUDIO

outside holes.

COAXIAL

OPTICAL

(red)

(white)

(orange)

Bracket (AAX34790)

(option)

DIGITAL

DVD

Screw (AAX12390)

(option)

Left and right

Optical digital

Coaxial digital

analog audio

COAXIAL

audio cable

OPTICAL

cable plugs

plug

DTV-CBL

DVD

Video jacks and cable plugs

COMPONENT VIDEO

VIDEO

(green)

(blue)

(red)

(yellow)

Composite video

Component video

cable plug

(U.S.A. model only)

XM Connect-and-

4 4 4 4 4

Play digital antenna

Connect the XM Connect-and-Play digital

antenna accessory (sold separately) to the

XM jack.

1 1 1 1 1

Surround speakers

Right

2 2 2 2 2

Left

Connecting to the

Antennas

receiver terminals of

the Antennas

Locate AM loop antenna and

indoor FM antenna, and connect to

the receiver. For more details, refer

to the "HTR-5930 Owner's

Manual".

MULTI CH INPUT

AUDIO

VIDEO

COMPONENT VIDEO

TUNER

DVD

FRONT

DVD

DTV/

ANT

CBL

DTV/

SURROUND

CBL

GND

DIGITAL

INPUT

SUB

CENTER

WOOFER

VCR

DVD

V-AUX

ANT

COAXIAL

OPTICAL

DTV-CBL

VCR

MONITOR OUT

(PLAY)

OUT

SURROUND

CENTER

MD/

DVD

CD-R

OUT

SUB

(REC)

WOOFER

MONITOR

OUT

AUDIO

OUTPUT

Subwoofer

cable

Connecting to the speaker or the receiver terminals

Press and hold the terminal tab, as shown in the figure below.

Insert the bare wire core.

Release your finger from the tab to allow it to lock securely on the bare wire core.

Test the security of the connection by pulling gently on the cable at the terminal.

Speaker terminals

red (+)

black (-)

Note:

Do not insert the

insulation coating into

the hole. The sound may

not be produced.

Subwoofer

To AC outlet

1 1 1 1 1

2 2 2 2 2

Cable TV or satellite tuner

DVD player

1. Connect the component video output jacks of your cable TV

1. Connect the component video output jacks of your DVD

or satellite tuner to the COMPONENT VIDEO (DTV/CBL)

player to the COMPONENT VIDEO (DVD) jacks of this

jacks of this unit using a component video cable.

unit using a component video cable.

2. Connect the optical digital audio output jack of your cable

2. Connect to the optical digital audio signal output jack of

TV or satellite tuner to the DIGITAL INPUT (DTV/CBL)

your DVD player to DIGITAL INPUT (DVD,COAXIAL)

jack of this unit using an optical digital audio cable.

jack using an optical digital audio cable.

Video out

Digital out (optical)

Digital out

(Component)

(coaxial)

MULTI CH INPUT

AUDIO

VIDEO

COMPONENT VIDEO

TUNER

DVD

FRONT

DVD

DTV/

ANT

CBL

SURROUND

DTV/

GND

CBL

INPUT

SUB

CENTER

WOOFER

VCR

V-AUX

ANT

VCR

MONITOR OUT

FRONT

SURROUND

CENTER

(PLAY)

OUT

MD/

CD-R

OUT

SUB

(REC)

WOOFER

MONITOR

OUT

AUDIO

OUTPUT

Audio in

Audio out

Audio in

Audio out

6 6 6 6 6

CD recorder or MD

5 5 5 5 5

DVD recorder or VCR

recorder

1. Connect the component video output jacks of your DVD recorder or

Connect the analog audio output jacks of your CD recorder

VCR to the COMPONENT VIDEO (VCR) jacks of this unit using a

or MD recorder to the MD/CD-R IN (PLAY) jacks on this

component video cable.

unit using an analog audio cable (stereo).

2. Connect the analog audio output jacks of your DVD recorder or VCR to

y To record audio sources output at the MD/CD-R OUT

the AUDIO VCR IN jacks on this unit using an analog audio cable.

(REC) jacks, you need to connect the source component

y To record audio and video sources output at the VCR OUT jacks, you

using an analog connection. For details, refer to the

need to connect the source component using an analog connection. For

"HTR-5930 Owner's Manual".

details, refer to the "HTR-5930 Owner's Manual".

3 3 3 3 3

Front speakers

Connecting to the

Left

Right

receiver terminals of

the front speakers

Loosen the knob.

Insert the bare wire core of the

speaker cable into the hole on

the terminal.

Tighten the knob to secure the

wire.

HTR-5930

IMPEDANCE SELECTOR

SPEAKERS

CLASS 2 WIRING

FRONT

red (+)

Receiver terminals

5 5 5 5 5

black (-)

Center speaker

3 3 3 3 3

Video monitor

Connect the component video input jacks of video

monitor to the COMPONENT VIDEO (MONITOR

OUT) jacks of this unit using a component video

cable.

Video in

(Component)

Video out

(Component)

HTR-5930

IMPEDANCE SELECTOR

SPEAKERS

CLASS 2 WIRING

FRONT

Video out (Component)

Video in

7 7 7 7 7

Plug in the power

After you complete all cable connections,

plug in the receiver, subwoofer, DVD player

and other components to the AC outlet.