Yamaha AX-492, AX-592, AX-892 Manual do Proprietário - Página 5
Procurar online ou descarregar pdf Manual do Proprietário para Amplificador Yamaha AX-492, AX-592, AX-892. Yamaha AX-492, AX-592, AX-892 24 páginas. Natural sound stereo amplifier
Imprimir página
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1.
To assure the finest performance, please read this manual
carefully and keep it in a safe place for future use.
2.
Install this unit in a cool, dry and dust-free area. Do not place it in
direct sunlight or near sources of heat (e.g., a stove, etc.). Make
sure that it is well ventilated and not exposed to rain or moisture
and that it is on a flat, stable surface, free from vibration.
3.
Never open the cabinet. If something drops into the unit, contact
your dealer.
4.
When moving the unit, first disconnect the AC power plug and the
cables which are connected to other equipment. Never pull the
cables or use excessive force on switches or controls.
5
.
The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly, damaging the unit or causing a fire. Avoid
blocking the ventilation openings and make sure that the unit is
well ventilated. Allow at least 30 cm (12 in) of space above the
unit and 20 cm (8 in) of space on the sides and rear.
Always set the VOLUME control to " ∞ " before playing the source.
6.
Increase the volume gradually to a desired level after the source
has started playing.
7.
Use a clean, dry cloth to clean the unit. Do not use chemical
solvents which might damage the finish.
8.
Be sure to read the "TROUBLESHOOTING" section before
deciding that the unit is faulty.
9.
When not planning to use this unit for long periods of time (e.g.,
vacation, etc.), disconnect the AC power plug from the electrical
outlet.
10.
To prevent damage from lightning, disconnect the AC power plug
and antenna cable when there is an electrical storm.
11.
Make sure that the unit is always properly grounded and
polarized.
12.
Do not connect audio equipment to the AC outlet on the rear panel
if the equipment requires more power than the outlet is rated to
provide.
WARNING
Do not change the IMPEDANCE SELECTOR
switch setting while the power to this unit is on,
otherwise this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
POWER SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be
set to either end closely. If so, set the switch to
either end closely.
13.
Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage
outlet.
Voltages are 110/120/220/240 V AC, 60/50 Hz.
WARNING
To reduce the risk of fire or electric shock, do not expose the unit to
rain or moisture.
IMPORTANT
The serial number is located on the rear panel.
Please record the serial number of this unit in the space below.
Serial No.:
Keep this Owner's Manual in a safe place for future use.
Note
The unit is not disconnected from the AC power source as long as it
is connected to the electrical outlet, even if the unit itself is turned
off.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMERS
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
VOLTAGE SELECTOR
IMPEDANCE
SELECTOR
AC OUTLETS
SWITCHIED
100W MAX. TOTAL
A OR B : 4 MIN. /SPEAKER
A + B : 8 MIN. /SPEAKER
A OR B : 6 MIN. /SPEAKER
A + B :12 MIN. /SPEAKER
before plugging into the electrical
Example: AX-892
<General model>
5