Directed Xpresskit DBALL2 Manual de instalação - Página 7

Procurar online ou descarregar pdf Manual de instalação para Acessórios para automóveis Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 16 páginas. Ford5 remote start ready (rsr) installation
Também para Directed Xpresskit DBALL2: Manual de instalação (12 páginas), Manual de instalação (19 páginas), Manual de instalação (18 páginas), Manual (14 páginas), Manual de instalação (13 páginas), Manual de instalação (14 páginas), Manual de instalação (19 páginas), Manual de instalação (20 páginas), Manual de instalação (15 páginas), Manual de instalação e referência rápida (16 páginas), Manual de instalação (18 páginas), Manual de instalação (16 páginas), Manual de instalação (18 páginas), Manual de instalação (16 páginas), Manual (19 páginas), Manual de instalação (11 páginas), Manual de instalação (10 páginas)

Imprimir página
Directed Xpresskit DBALL2 Manual de instalação
Platform: DBALL2
Firmware:
CHRYSLER11 ange Extender

Module Programming

Refer to the
LED
Diagnostics section on page 11 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the
function programming is selected using Xpress
version of the application.
Warning!
To take advantage of advanced features, you must use Xpress
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the
Config for RXT
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The
DBALL
module
must
be connected to it. Failing to do so could damage
a.
To
ensure that the D2D communication between SmartStart and
Gray wire must be connected to a ground source (
loop must be cut (
Rev A
b.
Do
NOT
connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the
DBALL
D2D connector.
Connect SmartStart to
DBALL
OR
XL202 Installation
Connect
XL
202 to
DBALL
using the D2D port.
Wait until the LED turns
1
Note: To skip the transponder programming and use convenience features only, press
the programming button 5 times. The
Press on the Start/Stop button (
illuminates on Start/Stop switch). The
Note: If transponder programming was skipped, the
2
for 3 seconds then shuts off once the module is successfully programmed
without bypass.
Note: During the programming sequence, the ignition on the car will be turned
ON
and
OFF
multiple time automatically.
3
Press Push-To-Start (
You have successfully completed the
R
Ready
XL
202 or SmartStart module to
VIP
(version 4. or higher). Visit www.directechs.com to download the latest
button.
be disconnected from any power source before SmartStart can
DBALL
Rev B
SmartStart).
using the D2D port.
ON
solid red.
LED
will turn orange then proceed to step 2.
PTS
)
once
to turn the ignition
LED
will flashes orange slowly.
PTS
) button once to turn ignition
module
programming sequence.
(RXT)
Installation
DBALL
, it is important to ensure that the proper feature and
5
VIP
4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select
FLASH YOUR MODULE
instructions.
.
DBALL
works properly, the
SmartStart), and the Brown or Blue
ON RUN
("
LED
turns
ON
solid orange
OFF
.
Go to the next page t complete the
o
XKL
oader3.
and follow the on screen
SmartStart
XL202
"
ENGINE
PUSH 1
x
START
STOP
ENGINE
START
STOP
web

programming.

© 2017 Directed. All rights reserved.
Rev.: 20170724
Page 7
Solid
&
Flashes
Slowly
PUSH 1
x