Platform: DBALL/DBALL2
Firmware: FORD5 Remote Start Ready (RSR) Installation
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module
flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the
features is possible using the information on this page.
* Default Option
Feat.
Operation
Flashes/Options
1. No RF Output*
RFTD Output
1
2. RFTD Output
Type
3. SmartStart
1. Disabled
2. Safelock
Smart OEM
2
Alarm Control
3. Enabled*
Feature Programming
To enter feature programming routine
Turn the ignition ON, then OFF.
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will
repeat until a new command is entered.
Changing feature options
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the
DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to
change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will
change the option for the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
Other features can be programmed.
The feature programming can be exited.
Exiting feature programming
No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.
OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
Module is connected to a remote starter using a standard installation.
Module is connected to an XL202 using an RSR or RXT installation (when available).
Module is connected to SmartStart using an RSR or RXT installation (when available).
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command
will be executed at the beginning or end of the sequence; it must be controlled by the Remote
Starter.
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will
unlock at the beginning of the sequence, and relock after start and shutdown.
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm
the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm
control must often be done by lock or unlock operation. This could create unnecessary actions
on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will
monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle
is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart
OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is
not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with
this option and will make it invisible to the user.
Description
Programming
Button
© 2016 Directed. All rights reserved.
Rev.: 20160317
Page 13
Imprimir página