Clarke WOODWORKER CDS1 Instruções de funcionamento e manutenção - Página 6

Procurar online ou descarregar pdf Instruções de funcionamento e manutenção para Lixadeira Clarke WOODWORKER CDS1. Clarke WOODWORKER CDS1 6 páginas. Detail sander

Imprimir página

Electrical Connections

This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for

connection to a standard, domestic electrical supply. Should the plug need changing at

any time, ensure that a plug of identical specification is used.

WARNING

This appliance is Double Insulated, and the two wires in the mains lead should

be wired up in accordance with the following colour code:

BLUE

BROWN

•

Connect the BLUE coloured cord to the plug terminal marked a letter "N"

•

Connect the BROWN coloured cord to the plug terminal marked a letter "L"

If this appliance is fitted with a plug which is moulded on

to the electric cable (i.e. non-rewireable) please note:

1. The plug must be thrown away if it is cut from the

electric cable. There is a danger

of electric shock if it is subsequently

inserted into a socket outlet.

2. Never use the plug without the fuse

cover fitted.

3. Should you wish to replace a

detachable fuse carrier, ensure that

the correct replacement is used (as

indicated by marking or colour code).

4. Replacement fuse covers can be

obtained from your local Clarke dealer or most electrical stockists.

FUSE RATING

The fuse in the plug must be replaced with one of the same rating (5 amps) and this

replacement must be ASTA approved to BS1362.

If in doubt, consult a qualified electrician. Do not attempt any electrical repairs yourself.

CABLE EXTENSION.

Always use an approved cable extension suitable for the power rating of this tool (see

specifications), the conductor size should also be at least the same size as that on the

machine, or larger. When using a cable reel, always unwind the cable completely.

-5-

NEUTRAL

LIVE

Operation

Fitting Sanding Pad.

a) Select pad to be used. (MUST be correct pads with velcro fitting ability).

b) Ensure sander is switched OFF and plug is removed from socket.

c) Line up holes in pad with those on machine pad. (this is necessary for dust

extraction), press pad firmly onto machine pad to secure it.

Dust Collection.

The dust collection bag/suction, (not supplied), is fitted to sander duct on sander

handgrip, below the mains cable.

Note :

If using a dust bag, it must be emptied regularly, do not wait until it is completely full.

To operate, insert the plug into the mains socket and switch ON, Holding the sander with

both hands, slide ON/OFF switch (located on top of the machine) forwards, the motor will

now run at full speed.

Offer sander to workpiece and work slowly backwards and forwards across the area to be

sanded until finished. Remove sander from workpiece and slide switch backwards to switch

OFF, (Wait until machine has stopped completely before putting it down.

Maintenance

Always inspect the tool before use, and ensure it is in top condition.

Ensure all air vents are clear, (use compressed air to clean the machine where possible).

Check the power cable to ensure it is sound and free from cracks, bare wires etc. avoid

using solvents when cleaning plastic parts, most plastics are susceptible to damage from

the various types of commercial solvents.

All bearings etc., in this tool are lubricated with a sufficient amount of high grade lubricant

for the tools lifetime under normal operating conditions, therefore no further lubrication is

required.

Trouble Shooting

Sander is overheating

This indicates the machine is dirty. Clean the ventilation holes, and blow out with compressed

air or clean with a dry cloth.

Overloading the machine will also cause overheating. Do not use for heavy duty work, and

do not apply excessive pressure.

Excessive sparking occurs

This indicates worn brushes. This problem is quickly remedied but you should consult your

CLARKE dealer for parts and advice.

Sander does not operate when switched ON

Check to ensure the fuse is sound and replace if necessary. If the fuse is sound or the blows

-6-