Directed Electronics 4103 Series Manual de instalação de referência rápida - Página 2
Procurar online ou descarregar pdf Manual de instalação de referência rápida para Alarme para automóvel Directed Electronics 4103 Series. Directed Electronics 4103 Series 2 páginas. Remote start with keyless entry; multi-button remote
Também para Directed Electronics 4103 Series: Manual de instalação (20 páginas)
Imprimir página
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1.
Turn the ignition on, then off.
2.
Select a Menu. Within 10 seconds, Press and hold the Valet button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2
honks indicates menu 2.
3.
When the desired menu LED flashes and honks are heard, release the Valet button.
4.
Select a Feature. Within 10 seconds, Press and release the Valet button the number of times correspond-
ing to the feature you wish to change. Then press and hold one more time to select the feature. The LED
flashes and the horn honks to indicate which feature is selected.
5.
Program the Feature. While holding the Valet button, you can program the feature using the remote
control.
For features with only two options;
= option 1 while
= option 2.
For features with more than two options;
selects the options in ascending order.
AUX
AUX
The LED flashes and the horn honks indicating which option is selected.
AUX
Once a feature is programmed:
•
Other features can be programmed within the same menu
•
Another menu can be selected
•
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press and release the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2.
Then press the Valet button once more and hold it.
To select another menu:
1.
Press and hold the Valet button.
2.
After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
•
The ignition is turned On
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These additional features and the adjust-
ments that may be programmed are described in the table below.
Menu Item
Feature
Default
1
Engine Runtime
12 min.
2
Diesel start type
Off
3
Diesel start delay time (seconds)
15 sec
4
Virtual Tach Fine Tune
Not initialized
5
Remote control programming
Unlocked
6
Feature Programming
Unlocked
© 2011 Directed Electronics. All rights Reserved.
Feature Menus
Default settings are in bold type.
Menu 1
Feature #
Feature
1
Horn function
2
Ignition con-
trolled lock
3
Ignition con-
trolled unlock
4
Doorlock out-
put duration
5
Double pulse
unlock
6
Double pulse
lock
7
Factory Alarm
Disarm func-
tion
8
Factory Alarm
Disarm Pulses
9
Comfort
Closure
10
Panic
Menu 2
Feature #
Feature
1
Engine check-
ing
2
Engine
Runtime
3
Park light
output
4
Cranking time
5
Activation
pulse count
6
2nd Ignition
behavior
7
Accessory
Options
output
8
2nd Status
1-60 min.
behavior
Timed
9
Anti-grind
1-90 sec.
0 to 1 second in 50 millisecond
10
Diesel start
increments
delay
Locked
11
Timer mode
run time
Locked
Opt. 1
Opt. 2
Opt. 3
Opt.4
Off
Siren
Siren
Siren
20 mS
30 mS
40 mS
On
Off
On
Off
0.8 sec.
3.5 sec.
0.4 sec.
Off
On
Off
On
with unlock
Before unlock
Remote start
only
Single
Double
Comfort
Off
Comfort
Closure 1
Closure 2
On
Off
Opt. 1
Opt. 2
Opt. 3
Opt.4
Virtual tach
voltage
Off
tachometer
12 min
24 min
60 min
Pulsed
Constant
0.6 sec.
0.8 sec.
1.0 sec.
1.2 sec.
1 pulse
2 pulses
3 pulses
Ignition
Accessory
Off during
On during
wait-to-start
wait-to-start
Normal
Latch rear
Pulse rear
defogger
defogger
On
Off
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
12 min
3 min
6 min
9 min
Remote Programming
1.
Turn key to the ON position
2.
Within 10 seconds, press and release Valet button one time.
3.
Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks
(if connected) to confirm entry into remote programming.
4.
Press the
button on the remote control.
Opt. 5+
5.
The horn honks to confirm the remote has been programmed.
AUX
6.
Release the Valet button, and turn the key to the Off position.
Siren
7.
The horn sounds one long honk to confirm that remote programming has been exited.
50 mS
The programming routine exits if any of the following occurs:
•
The ignition is turned off
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Basic Remote Functions
Button
AUX
AUX
A U X
A U X
Opt. 5+
1.4,
1.6,
1.8,
2.0,
4.0 sec
Directed Logo Usage
Bitwriters with a date code of 6a or older require an IC
upgrade (p/n 998M). Some bitwriters with a date code
of 6B do not require the IC upgrade, refer to tech tip #
1112 for more information.
Logo, Directed with designed in USA.eps
See full Installation Guide for more
detailed information on this system.
Such information and more can be
found online at:
www.directechs.com
Logo, Directed Electronics w-driven.eps
Function
LOCK
UNLOCK
TRUNK RELEASE
REMOTE START
AUX
The Bitwriter® (p/n 998U) re-
quires chip version 2.7 or newer
to program this unit.
QRN4103 2011-12
2