Directed Electronics Ready Remote 23926 Manual de instalação - Página 2

Procurar online ou descarregar pdf Manual de instalação para Arrancador remoto Directed Electronics Ready Remote 23926. Directed Electronics Ready Remote 23926 19 páginas. Remote control car starter

Imprimir página

Directed Electronics Ready Remote 23926 Manual de instalação

On cars with airbags, you may notice bright yellow tubes

or harnesses marked SRS (Supplemental Restraint Sys-

tem) underneath the steering column area. DO NOT tamper

with these wires in any way, to prevent personal injury

and/or damage to the air bag system.

On GM rear-wheel drive vehicles built prior to 1995 and

Dodge Dakota trucks built prior to 1996, see the last page

of this instruction manual.

Battery gases are explosive.

Do not smoke while working near the car's battery.

Note: Some installers connect a battery charger to the vehicle's

battery during installation. This is fine, but it must be removed be-

fore running the vehicle under remote starter control.

When running the wires through the car's firewall, be sure

to protect them from sharp metal edges and from hot

surfaces on and around the engine.

INSTALLATION INSTRUCTIONS

1. Before You Start

Take the time to read through the whole installation manual before

beginning.

Always leave a window open to avoid locking your keys in your car.

IMPORTANT: After having read the entire manual, start the installation

by putting the yellow WARNING STICKER in the engine compartment.

Choose a surface that is clean and readily visible when the hood is

open.

This car is equipped with a remote control starting

Disable before working on car!

AVERTISSEMENT

Ce véhicule est équipé d'un systéme de démarrage a distance.

POWER & IGNITION HARNESS

The remote starter module will be installed under the dash once all

wiring has been completed. Do not mount the module at this time!

You will need to check the red diagnostic LED light as the instal-

lation progresses. Locate (or drill) a hole in the firewall to run the

PURPLE and GREEN wires of the Control Harness and the PINK wire

of the Power harness into the engine compartment. The remaining

short wires stay in the passenger area. Leave about a foot of the wire

harness under the dash for ease of working and visual access to the

diagnostic light.

The Installation Information section of our website

www.designtech-intl.com and www.directed.com are available

24 hours/day to provide you with free, up-to-date vehicle wiring

information for your particular vehicle after you log in.

Note: Always connect the Pink and Black wires before connecting

any of the other wires. Do not insert the fuse until step 11.

2. Black Wire (16 AWG) - Ground

Connect the BLACK wire to a very good, clean chassis ground in the

driver's kick panel area. Use the small ring terminal. (The metal

bracing around or beneath the dash board is not always adequate.)

3. Pink Wire (12 AWG) - Power (+12 Volts)

Connect the ring terminal at the end of the short PINK wire to the +12

Volt terminal of the battery. Run the long pink wire through the

firewall of your vehicle. Join the remaining ends of the power wire

together by soldering them. Tape with electrical tape to leave no

v5.3 (2126)

WARNING

device.

exposed wires. Alternatively, you may wish to use the yellow butt

connector, but we recommend soldering. Wait to insert the 30 amp

green fuse into the holder until step 11. As the power is first applied

to the unit the red diagnostic LED light will blink once.

Note: Failure to properly install the fuse holder and 30 amp fuse to

the pink wire to the battery voids all product warranties.

Ignition Key Diagram for Steps 4-7

The vehicle's wires are found coming off of

the key switch. Remove the panel under the

steering column to access these wires.

4. Blue Wire (14 AWG) - Ignition 1

Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire

will measure +12 Volts on the test meter in the "run" and "start"

position, and is off in the "lock/off" and "accessory" position.

5. Green (14 AWG) - Ignition 2

Connect the GREEN wire to the Ignition 2 wire in the vehicle. The

Ignition 2 can function in serveral different ways in your vehicle. It is

important to understand how it works. The Ignition 2 will usually mea-

sure +12 Volts in the "run" position and is off (ground) in the "lock/

off" and "accessory" position. In certain vehicles, it may also show

+12 Volts in the "Start" position or Ignition 2 may turn OFF during

"Crank" and turn back ON after the starter disengages. Carefully note

the function of the Ignition 2 wire. If the Ignition 2 turns OFF during

"Crank," see Changing Ignition 2 Function in section 21. If Ignition 2

stays ON during "Crank," no options need to be changed.

6. White Wire (14 AWG) - Accessory

Connect the WHITE wire to the accessory wire which is +12 Volts in

the "run" and "accessory" position, but off in the "start" and "off"

positions. In GM vehicles, connect the white wire to the (usually or-

ange) wire that is hot in "run" only.

7. Yellow (14 AWG) – Starter

Connect the YELLOW wire to the starter wire. This wire will measure

+12 Volts on the test meter in the "start" position only.

Note: Most Nissan vehicles have two starter wires. Connect both

starter wires of the vehicle to the YELLOW start wire of the remote

starter.

8. Plug-In On/0ff Switch

Connection of the ON/OFF control switch is mandatory. Do not let the

switch wires touch ground. Mount the control switch so that it is

easily accessible and so that the "ON" position is facing upward.

Make sure there is enough clearance behind the mounted switch for

the wire connections. Use a 1/4" drill-bit for the mounting hole. Plug

the switch connector into the module just to the right of the power

wires. Turn the switch on.

CONTROL HARNESS

(ALL WIRES ARE THE SMALLER 18 AWG SIZE)

9. Purple Wire - Hood Pin Switch - Control Harness

The hood pin switch MUST be installed with

the remote starter. It prevents operation of

the remote starter when the hood is open

and is used to initialize the unit. Connect

the PURPLE wire to the hood pin switch us-

ing the red connector.

Note: If you already have a hood pin switch

which is being used by a car alarm system,

To Alarm

To Remote Starter

How to share a hood pin

switch with an alarm