Directed Electronics Ready Remote 23927 Manual de instruções - Página 5
Procurar online ou descarregar pdf Manual de instruções para Arrancador remoto Directed Electronics Ready Remote 23927. Directed Electronics Ready Remote 23927 20 páginas. Remote control car starter
Imprimir página
remote starter module. In some vehicles you will get better range
performance if the antenna is pointing vertically downward from the
top of the windshield.
The wiring section of the installation is now complete. Be sure to
cap all unused wires so as to prevent short circuits, and mount the
module securely under the dash. When tying up and mounting the
unit, be sure to avoid any moving parts (steering column, ped-
als) and sharp edges.
21. Troubleshooting with the Self Diagnostics
The remote starter contains a built in diagnostic routine that will
indicate why the unit started or why the unit turned off the car the
last time that the unit was used.
To activate the diagnostic mode for why it turned off, simply turn the
On/Off control switch to the "OFF" position. In a few seconds, the
red LED on the module will flash 1 to 12 times to identify the prob-
lem. See the chart below for an explanation of the flashes:
1 flash
10/15 minute time out. Unit should be fine. Make sure
the transmitter is working properly.
2 flashes
Unit turned off because Brake or Hood was activated.
Check to make sure the hood pin switch is depressed
when the hood is closed and the correct brake wire is
hooked up.
3 flashes
No Tach or Stalled. Review Step 12 and make sure the no
tach/tach wire option is programmed correctly.
4 flashes
Received another remote input from the transmitter
5 flashes
Transmission was shifted into gear. Move the In-Gear
switch inside the receiver module to the OFF position
(see diagram below for location of In-Gear switch).
6 flashes
Low battery voltage, or may be missing an ignition wire
which powers up the alternator
8 flashes
Over current - One of the 400 mA (-) transistor outputs
(Lock, unlock, horn, lights, trunk, or Ignition #3) of the
control harness is driving too much current. Make sure
to use a relay where necessary.
12 flashes The Control Switch was turned off while the starter was
running.
22. Setting Program Features:
The remote starter has many special features available. You will not
need to use these special features in most situations. The factory
settings will operate most vehicles. You must turn the On/Off control
switch to the "OFF" position to program any features. Note that when
turning off this control switch, the red LED light will flash a few times,
giving the diagnostic code described in the Troubleshooting (Section
21). Wait a few seconds for it to finish before programming your new
Options.
© 2005 Directed Electronics, Inc.
Feature # Factory Setting (2 flashes) Option (1 flash)
1
"No-Tach"
2
10 Min. Run Time
3
Normal Crank
4
Normal
5
N/A
6
N/A
7
"Enable" feature
8
N/A
Option #1
No-Tach
This option sets the starting method. The factory setting uses "No-
Tach" starting. If you wish to use the tach to start, follow the instruc-
tions in the Tach Rate Learning section (step 13B).
Option #2
10 Min. Run Time
This option gives you a choice of run times.
Option #3
Normal Crank
This option will add 50% more crank time to the NoTach™ starting
feature.
Option #4
Normal
This option will add 100% more crank time to the NoTach™ starting
feature.
Option #7
"Enable" Feature
This option cancels the "enable" mode safety feature. The "enable"
mode requires that the driver toggle the ON/OFF control switch "OFF"
then "ON" each time the driver removes the key from the ignition in
order to "enable" the vehicle for remote starter control. This feature
guards against undesired starting of the vehicle by remote control.
You must keep this option as enable on all GM rear wheel drive and
Dodge Dakota vehicles manufactured prior to 1996.
Programming An Option:
If you want the factory setting, DO NOTHING and skip this section. If
you want to change one or more of the features, TURN THE ON/OFF
CONTROL SWITCH TO THE "OFF" POSITION. Wait for the red LED
light to stop flashing, then continue with the following procedures:
A.
For options 1-7: Push the white code button on the remote start
module. Each time you push the button the red LED light will
flash 1 to 7 times signifying at which feature you are (press it
once, the red LED light flashes once. Press it again and it will
flash two times. Press it again and it will flash three times, etc.,
to show what feature you are at).
B.
When you are at the feature level you desire, push the start
button on the transmitter for 1 second and the red LED light will
flash once to signify you are at the Option setting. You can push
the transmitter button again and it will flash twice to signify you
are at the Factory setting. Push the transmitter button again and
you will go back to the Option setting (one flash).
C.
You can choose to change another feature by starting over again
at Step A. After six seconds, the remote starter automatically
exits the programming mode (three red LED light flashes).
D.
When finished – switch the Control Switch back ON. The red
LED light will flash once.
23. Changing Ignition 2 Function
Many newer vehicles turn off the Ignition 2 wire while the starter is
cranking. In these vehicles it is very important to have the remote
starter copy the starting sequence of the key exactly; otherwise the
vehicle's computer may show a fault code.
5
Tach Mode
15 Min. Run Time
Extended Crank
Super Crank
N/A
N/A
No "Enable"
N/A
Tach Mode
15 Min. Run Time
Extended Crank
Super Crank
No "Enable"
v5.3 (27)