Directed Electronics XPRESSKIT DLPKCHG1-CHRY2 Manual de instalação - Página 3
Procurar online ou descarregar pdf Manual de instalação para Acessórios para automóveis Directed Electronics XPRESSKIT DLPKCHG1-CHRY2. Directed Electronics XPRESSKIT DLPKCHG1-CHRY2 4 páginas. Solex series upgradeable doorlock interface + 1st gen. sentry key transponder bypass
Imprimir página
STEP #1 MODULE PROGRAMMING
Connect module to the 10-pin harness and
1
4-pin D2D (if installed in D2D mode), LED
will go ON to confirm correct connection.
Insert the key and turn to the ON position
2
(without starting the engine). When the LED turns
off, the module is programmed, remove the key.
STEP #2: TRANSPONDER PROGRAMMING MODE
(You will need 2 valid keys)
1
Set the remote starter in diesel engine type.
A) P
lace the loop antenna ring
ar
ound the vehicle's ignition
cylinder as shown.
2
B) Plug the 2 pin loop antenna
ring connector into the 2 pin
connector of the module.
Insert the first valid key into the ignition switch and turn it
3
ON for at least 5 seconds, but no longer than 15 seconds.
4
Turn the ignition switch OFF and remove the first key.
Within 5 seconds insert the second valid key and turn
5
the ignition switch ON.
After 10 seconds a chime will sound and the security light will begin
6
to flash. Turn the ignition switch OFF and remove the second key.
Within thirty (30) seconds, press the remote start button and the
7
remote starter will turn the ignition ON but will not crank.
The security light will turn ON, then start flashing; it will come ON again for
8
2 seconds then turn OFF to confirm the transponder is now programmed.
You can now apply brakes to disable the remote starter sequence.
To complete the installation, program the remote starter to the
9
desired engine type (gas or diesel) and then test your installation.
DLPKCHG1-CHRY2
THEN
KEY
KEY
THEN
THEN
OFF
Note: Move antenna
loop as close to the
front of the ignition
cylinder (factory
receiver ring) as
possible.
KEY#1
KEY#1
KEY#2
KEY#2
Security
STEP #3 USER SETTINGS
(Optional programming.
Insert key into ignition at the "OFF"
1
position. Press and hold
programming button for 2 seconds,
LED will flash rapidly for 2 seconds.
ON
Release programming button, LED
will identify the MODE selection
2
with a slow flash pattern (6, 7 or 8
slow flashes) and then will identify
OPTION selection with a fast flash
pattern. (1 or 2 fast flashes)
To change MODE, press
and release the
3
programming button once,
DIESEL
LED will confirm MODE with
a slow flash pattern (6, 7 or 8
slow flashes).
To change OPTION SELECTION
within a MODE, press LOCK or
4
UNLOCK button on the aftermarket
remote control system. The LED
will identify option selection with
either one or two fast flashes.
To save and exit programming,
press and hold programming
5
button until LED flashes once
rapidly, showing end of MODE &
OPTION programming.
MODE 6 - Lock when remote starter stops
Option 1: Activate (default)
Option 2: Deactivate
MODE 8 - Reset
Option 1: No reset (default)
Brake
Option 2: Complete reset of option and module
pedal
DIESEL
Only MODES 6, 7 & 8 are available)
KEY
PRESS AND
HOLD 2 SEC
THEN
SLOW FLASH
RELEASE
(MODE)
THEN
SLOW FLASH
PRESS & RELEASE
(MODE)
(
(
or
THEN
PRESS 1x
FAST FLASH
(OPTION)
PRESS & HOLD
Modes & Options list
MODE 7 - Vehicle with or without alarm
Option 1: Vehicle with alarm (default)
Option 2: Vehicle without alarm
© 2010 Directed Electronics. All rights reserved.
Rev.: 20100224
Page 3 to 5
THEN
FLASH 2 SEC
THEN
FAST FLASH
(OPTION)
SLOW FLASH:
6 TIMES = MODE 6
7 TIMES = MODE 7
8 TIMES = MODE 8
FAST FLASH:
ONCE = OPTION 1
TWICE = OPTION 2
UNTIL
FLASH ONCE
RAPIDLY