Clarke XR 155 Manual de operação e manutenção - Página 7
Procurar online ou descarregar pdf Manual de operação e manutenção para Aquecedor Clarke XR 155. Clarke XR 155 8 páginas. Paraffin/diesel heaters
Também para Clarke XR 155: Instruções de funcionamento e manutenção (20 páginas)
Imprimir página
Bi-Monthly
Fan.
Having removed the top cover, thoroughly clean the fan using a cloth moistened
with paraffin or light solvent, and dry using an air line if possible.
Output Air Filter.
Remove the grille, and pull off the Intake Air Filter, revealing the 3 screws securing
the filter housing. Remove the screws and pull off the housing to reveal the Output
Air Filter. If contaminated, this filter must be renewed.
In dusty environments this procedure should be carried out, monthly
Nozzle.
Having removed the top cover, gently unscrew and remove the burner head,
and unscrew the nozzle. Clean, using compressed air and a soft brush, if
necessary. DO NOT prod or poke the nozzle in any way, with a metal tool.
Following a period of Storage.
Pump Pressure.
Before putting the heater back into service, following a period of storage, you
should carry out all checks previously specified. In addition, you should test and
adjust if necessary, the Air Pump Pressure, as follows:
Near the centre of the Grille, is a cut-out to accommodate the Air Pump Pressure
Relief Valve, and a plug for installing a Pressure Gauge as shown in fig. 5.
Remove the plug, and install a gauge with a resolution of at least 0.02 bar (0.3psi).
Start the heater, and observe the pressure reading, which should be as follows:
Model
Air Pump Pressure
XR75
0.26 - 0.33bar (3.84 - 4.8psi)
XR105
0.30 - 0.36bar (4.45 - 5.3psi)
XR155
0.30 - 0.39bar (4.45 - 5.7psi)
To adjust the pressure, insert an Allen key into the hex socket in the end of the Relief
Valve Adjuster, and undo the Adjuster Nut. Turn the Allen key clockwise to
increase pressure, and anticlockwise to decrease. Tighten the securing nut when
the correct pressure is reached, ensuring the Allen key does not turn in the process.
Fig. 5
10
1. The Fuel System.
Fuel is held in the tank at the base of the system, at atmospheric pressure. An air pump,
mounted on the end of the motor, draws air through a filter, compresses it, and forces it
through a second filter, and via an air line, directly to the burner head nozzle. The speed
of the air over the nozzle, causes a depression. Fuel is therefore forced up the tube by
atmospheric pressure, through a filter, and out of the nozzle in the form of a spray.
It is important to ensure that the vent in the filler cap is not blocked at any time, otherwise
fuel will not reach the nozzle.
This heater is capable of burning
Paraffin or Diesel oil. NEVER use petrol.
As these fuels burn at different
rates, provision is made to ensure
that the correct volume of air is
allowed
into
the
combustion
chamber for each type of fuel.
This is achieved by means of a
blanking plate, at the rear of the
burner, shown in Fig. 3,
The blanking plate is factory set to burn PARAFFIN, so that tab'A' covers vent 'B'
WARNING!
TO BURN DIESEL, THE BLANKING PLATE MUST BE MOVED TO THE POSITION SHOWN IN
FIG.3, OTHERWISE DAMAGE TO THE COMBUSTION CHAMBER WILL OCCUR
NOTE: In the case of MODEL XR75, there is insufficient room to store the blanking plate in the
position shown. The plate should therefore be removed and retained for possible future use.
2. The Air System.
Additional air is supplied to the combustion chamber by a fan, which is mounted on
the opposite end of the motor shaft to the Air Pump. Openings around the burner
head allow a portion of this air to be drawn into the combustion chamber, where it
mixes with the air and fuel from the nozzle, and ensures that all the fuel is burned,
preventing the emission of black smoke.
The remaining air is directed around and over the combustion chamber, until it
finally mixes with the heated air from the combustion chamber, and is ejected as
a jet of clean hot air.
3. The Ignition System.
A constant arc is struck between the electrodes, which ignites the air and fuel
mixture. It is important that the electrode gap is correctly maintained, otherwise
arcing will not take place...see Maintenance.
4. The Safety Control System.
A light sensitive photo cell (flame sensor) trips the motor if the flame goes out for
any reason, causing the heater to shut down.
Fig. 3
7