Blade CHROMA Manual de início rápido

Procurar online ou descarregar pdf Manual de início rápido para Quadricópteros Blade CHROMA. Blade CHROMA 2 páginas. Quadcopter with st10+ personal ground station and gopro compatible gph4 3-axis gimbal

Imprimir página
Blade CHROMA Manual de início rápido
1
Charge the Flight Battery (~75 min)
NOTICE: Refer to the "Charging Warnings" on the back of this page.
Charger LED codes
Power
Charging
a
connected
a
a
b
a
b
c
b
c
b
c
d
c
d
e
d
e
d
e
f
f
e
f
f
CAUTION: All instructions and warnings must be followed exactly. Mishandling
of Li-Po batteries can result in a re, personal injury and/or property damage.
5
Install Your Camera
The included GPH4 3-axis gimbal and MK58 video
transmitter are compatible with GoPro
®
3 and 4 cameras.
a
a
a
Connect the USB cable from the gimbal to
a
your camera USB port.
b
b
Install the camera into the gimbal by rotating
b
b
the mount as shown.
c
Slide the camera into the camera mount until
c
c
it stops against the front of the mount.
c
Thread the retaining screw into the mount
d
d
until it is snug against the camera. Do not
d
d
overtighten.
e
e
CAUTION: The GoPro
®
Wi-Fi will interfere
e
e
with the quadcopter receiver and may
cause a loss of signal and crash. Follow the camera
f
f
instructions to turn the Wi-Fi off before attempting
f
f
to power on the quadcopter. Crash damage is not
covered under warranty.
a
10
Understanding the Flight Modes
Smart Mode
• A green LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are green
• Intended for the beginner pilot
• Maximum distance of 100 m from
the pilot
For best results while using Smart Mode, it is recommended that the
pilot always turn to face the quadcopter while ying.
AP Mode
• A purple LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are purple
• Intended for the intermediate pilot
• Maximum distance of 100 m from
the pilot
NOTICE: If the Chroma
quadcopter loses GPS signal while ying in either Smart or AP Mode, the LEDs will ash rapidly for 2 seconds and then
™
once every second. The quadcopter will default to a stable ight mode with similar control response as AP Mode. Return Home will not function.
Please familiarize yourself with the controls in AP Mode to ensure a safe return of the quadcopter in the event of GPS signal loss.
For information on additional ight modes, including "Follow Me," see the online video at www.KnowChroma.com.
13
Throttle control
Left transmitter stick
• To maintain the current
altitude, allow the left
transmitter stick to return
to center.
Climb
Descend
QUADCOPTER WITH ST10+ PERSONAL GROUND STATION AND GoPro® COMPATIBLE GPH4 3-AXIS GIMBAL
M A N U A L
Install and Charge the ST-10+ Transmitter Battery
2
2
Charging
Balancing
complete
a
b
c
d
a
a
Insert the LiPo battery into
e
a
the ST-10+ transmitter.
Connect the battery lead
b
b
f
to the transmitter noting
b
the correct polarity.
c
c
Close the battery compartment.
c
d
d
d
6
Extend the GPS Mast
e
e
e
a
f
f
f
CAUTION: NEVER attempt
to y without extending the
GPS mast.
7
Install the Flight Battery
b
c
• Slide the fully charged battery in until it locks.
d
• Remove the battery by pressing the locking tab and
sliding the battery to the rear of the quadcopter.
Right transmitter stick
=
Stick commands move
the Chroma
quadcopter
™
relative to the pilot location
Right transmitter stick
=
Stick commands move
the Chroma
™
quadcopter
relative to its orientation
14
Flying and Landing
NOTICE: If you begin to lose control, release the control sticks and the
model will self-level.
Pay close attention to the LEDs while ying. If at any time the LEDs indicate the ight
battery voltage is low, as shown in the LED reference guide, land the quadcopter
immediately and charge the ight battery.
To land, you may either slowly lower the left transmitter
stick to descend and land, stopping the motors as
shown in step 12b:
or you may select "Return Home" on the top right switch on your transmitter:
The quadcopter will return to the start position, land and stop the motors. You may
cancel the return to home function by switching back to Smart or AP Mode on the
top right switch on your transmitter.
NOTICE: Return home will only function if the quadcopter has GPS lock.
a
a
b
b
c
a
c
d
b
Connect the USB
d
e
c
a
cable to an appropriate
USB power source and to the
charge port of the transmitter.
e
f
d
b
The screen will show a charging
battery icon. Disconnect the
USB cable when the onscreen
f
e
c
battery icon shows full capacity.
f
d
e
b
f
8
Power Up
a
Place the quadcopter
a
a
a
a
outdoors on a at,
c
level surface.
b
b
Set the top right
b
b
b
transmitter switch
a
to Smart.
c
c
c
c
Power on the
c
d
transmitter.
b
d
Power on the
d
d
d
quadcopter.
d
c
The LEDs will show
e
e
green, rotating counter-
e
e
e
clockwise around the motor pods
while the quadcopter acquires a
d
f
f
GPS signal. The front LEDs will
f
f
f
show white and the rear will show
e
green when the quadcopter is
ready for ight.
Perform the compass
f
calibration as shown in the
video at www.KnowChroma.com.
11
Placement at startup
Away from
the pilot
Home position
Toward
the pilot
SAFE Circle
™
Pilot location
Front
CAUTION: Starting the motors sets the home location. The quadcopter
must be approximately 16 feet (5 meters) from where the pilot will
stand during ight, pointing away from the pilot. If the aircraft is pointed in any
other direction, the SAFE Circle™ feature will not function as expected and may
result in personal injury or damage to property. Once the aircraft's motors are
started, do not change your position.
15
Controlling the Camera Gimbal
Use the Camera Tilt Slider to adjust
the vertical angle of the camera
gimbal.
Camera Tilt Slider
The buttons on the top of the ST-10+ have no function.
Solid red
For further information on controlling the 3-axis gimbal
with the ST-10 Ground Station, see the online video at
www.KnowChroma.com.
This aircraft is not compatible with Spektrum
3
Install the propellers
B
A
A
B
B
A
• The props and motor pods have a letter code, either
"A" or "B" molded in. Match the "A" props to the "A"
motor pods and the "B" props to the "B" motor pods.
• The "A" props thread on counter-clockwise.
• The "B" props thread on clockwise.
• Tighten the props only nger tight. DO NOT overtighten.
9
a
a
After the Chroma powers on, power on your camera.
a
The MK58 video transmitter will begin transmitting
b
a
video.
b
b
a
To link the MK58 transmitter signal to the ST10+:
b
a
a
c
b
a
c
b
c
b
b
d
c
b
c
d
c
d
c
c
e
d
c
e
d
e
d
d
e
d
e
e
g
e
e
The live video feed is now visible on the ST-10+ display.
Double tap on the image to expand the video to ll the
f
display. Double tap again to return to the main menu
with live video.
Front
16 ft
(5 m)
Pilot location
16
DSM
, DSM2
or DSMX
technology.
™
®
®
®
4
Install the 3-axis Gimbal
a
b
a
c
Slide the
a
gimbal on the
a
mount rails until it
b
d
locks.
b
a
Connect the
b
c
wiring har-
e
c
ness to the plug on
a
b
the bottom of the
c
d
quadcopter.
f
d
Connect the
b
c
d
2.5mm jack
e
from the gimbal to
e
c
the port in the MK58
d
e
video transmitter.
f
To remove the
f
e
d
gimbal, press the tab
f
at the front of the mount and slide the gimbal
forward.
e
f
Link the Camera to
the ST-10+ via Wi-Fi
f
Select Flight Settings from the main menu on
the ST-10+.
Select the Bind option.
Under Camera, select the LK58MINI_71000
network (LK58MINI_******).
Touch the Password line on the screen and enter
the password "12345678" on the touchscreen.
Select OK.
f
The ST-10+ will indicate a successful
f
connection. Select OK.
f
Return to the Main Menu.
f
f
f
f
12a
Motor Start
Hold 3 seconds
12b
Motor Stop
Hold until the motors stop
NOTICE: Do not press the Motor Stop button
while the aircraft is airborne. The motors could
stop, causing the aircraft to crash.
WARNING: Stopping the motors while the
quadcopter is still in ight will cause the
quadcopter to crash. Crash damage is not covered
under warranty.
After Your Flight
a
b
a
c
b
d
c
e
a
d
f
b
e
c
f
d
e