Blade Chroma BLH8675 Manual
Procurar online ou descarregar pdf Manual para Quadricópteros Blade Chroma BLH8675. Blade Chroma BLH8675 2 páginas. With cgo3 4k camera gimbal and st-10+ personal ground station transmitter
Imprimir página
1
Charge the Flight Battery (~75 min)
Charger LED codes
Power
Charging
a
connected
a
a
b
a
b
b
c
c
b
c
d
c
d
e
d
d
e
e
f
e
f
f
f
CAUTION: All instructions and warnings must be followed exactly. Mishandling
of Li-Po batteries can result in a fi re, personal injury and/or property damage.
4a
Remove the Gimbal Cover
Tip: Replace the gimbal cover after fl ying for storage and
transportation of the quadcopter to protect the gimbal.
5
Install the Flight Battery
8
Understanding the Flight Modes
Smart Mode
• A green LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are green
• Intended for the beginner pilot
• Maximum distance of 100 m from
the pilot
For best results while using Smart Mode, it is recommended that the
pilot always turn to face the quadcopter while fl ying.
AP Mode
• A purple LED cycles around the motor
pods counter-clockwise until GPS is
acquired
• Once GPS is acquired, the front LEDs
are white and the rear are purple
• Intended for the intermediate pilot
• Maximum distance of 100 m from
the pilot
NOTICE: If the Chroma
™
quadcopter loses GPS signal while fl ying in either Smart or AP Mode, the LEDs will fl ash rapidly for 2 seconds and then
once every second. The quadcopter will default to a stable fl ight mode with similar control response as AP Mode. Return Home will not function.
Please familiarize yourself with the controls in AP Mode to ensure a safe return of the quadcopter in the event of GPS signal loss.
For information on additional fl ight modes, including "Follow Me," see the online video at www.KnowChroma.com.
11
Throttle control
Left transmitter stick
• To maintain the current
altitude, allow the left
transmitter stick to return
to center.
Climb
Descend
WIT H CGO 3 4K CA ME RA G IMB A L A N D ST-1 0+ P ER SO N A L G R O UN D STATI O N TR A N SM I T TER *
M A N U A L
Install and Charge the ST-10+ Transmitter Battery
2
Charging
Balancing
complete
a
b
c
d
a
a
Insert the LiPo battery into the
e
a
ST-10+ transmitter.
b
Connect the battery lead to the
b
f
transmitter noting the correct polarity.
b
c
Close the battery compartment.
c
c
d
d
d
4b
Extend the GPS Mast
e
e
e
f
f
f
• Slide the fully charged battery in until it locks.
• Remove the battery by pressing the locking tab and
sliding the battery to the rear of the quadcopter.
Right transmitter stick
=
Stick commands move
the Chroma
™
quadcopter
relative to the pilot location
Right transmitter stick
=
Stick commands move
the Chroma
quadcopter
™
relative to its orientation
12
Flying and Landing
NOTICE: If you begin to lose control, release the control sticks and the
model will self-level.
Pay close attention to the LEDs while fl ying. If at any time the LEDs indicate
the fl ight battery voltage is low, as shown in the LED reference guide, land the
quadcopter immediately and charge the fl ight battery.
To land, you may either slowly lower the left
transmitter stick to descend and land,
stopping the motors as shown in step 10b:
or you may select "Return Home" on the top right switch on your transmitter:
The quadcopter will return to the start position, land and stop the motors.
You may cancel the return to home function by switching back to Smart or
AP Mode on the top right switch on your transmitter.
NOTICE: Return home will only function if the quadcopter has GPS lock.
a
a
b
b
c
a
c
d
b
a
Connect the USB cable to an
d
e
c
appropriate USB power source
and to the charge port of the transmitter.
b
The screen will show a charging battery
e
f
d
icon. Disconnect the USB cable when the
onscreen battery icon shows full capacity.
c
f
e
d
f
e
f
6
Power Up
a
a
a
a
Place the quadcopter outdoors on a fl at,
a
a
level surface.
b
b
b
b
Set the top right transmitter switch to
b
b
c
Smart.
c
c
c
Power on the transmitter.
c
c
d
d
d
Power on the quadcopter.
d
d
d
Perform the compass calibration
e
e
as shown in the video at
e
www.KnowChroma.com.
e
e
e
f
The LEDs will show green, rotating
f
f
counter-clockwise around the motor
f
f
pods while the quadcopter acquires a gps
f
signal. The front LEDs will show white and the
rear will show green when the quadcopter is
ready for fl ight.
9
Placement at startup
Away from
the pilot
Home position
Toward
the pilot
SAFE Circle
™
Pilot location
Front
CAUTION: Starting the motors sets the home location. The
quadcopter must be approximately 16 feet (5 meters) from where
the pilot will stand during fl ight, pointing away from the pilot. If the aircraft
is pointed in any other direction, the SAFE Circle™ feature will not function
as expected and may result in personal injury or damage to property. Once
the aircraft's motors are started, do not change your position.
13
Controlling the Camera
Use the buttons on the top of the ST-10+ to control the camera functions.
Photo
Button
Use the Camera Tilt Slider to
adjust the vertical angle of the
camera gimbal.
Camera Tilt Slider
Solid red
For further information on controlling
the CGO3 camera with the ST-10
Ground Station, see the online video
at www.KnowChroma.com.
* This aircraft is not compatible with Spektrum
3
Install the propellers
B
• The props and motor pods have a letter
code, either "A" or "B" molded in. Match
the "A" props to the "A" motor pods and the
"B" props to the "B" motor pods.
• The "A" props thread on counter-clockwise.
• The "B" props thread on clockwise.
• Tighten the props only fi nger tight.
DO NOT overtighten.
7
Connect the CGO3 Camera
to the ST-10+ via Wi-Fi
After the CGO3 camera powers on, the LED on the
gimbal will glow red for approximately 40 seconds.
When the LED changes to yellow, complete the
following steps to bind the CGO3 to the ST-10+:
b
• Select Flight Settings from the main menu on the
ST-10+.
• Select the Bind option.
a
• Under Camera, select the CGO3 network
(CGO3_******).
• Touch the Password line on the screen and enter
b
c
the password "1234567890" on the touchscreen.
• Select OK.
c
• The ST-10+ will indicate a successful connection.
Select OK.
• Return to the Main Menu.
d
The live video feed is now visible on the ST-10+
display.
e
Double tap on the image to expand the video to fi ll the
display. Double tap again to return to the main menu
with live video.
f
10a
Front
16 ft
(5 m)
10b
Pilot location
NOTICE: Do not press the Motor Stop button
while the aircraft is airborne. The motors could
stop, causing the aircraft to crash.
the quadcopter to crash. Crash damage is not
covered under warranty.
14
After Your Flight
Video
Start/Stop
Button
™
DSM
®
, DSM2
®
or DSMX
®
technology.
A
A
B
B
A
Motor Start
Hold 3 seconds
Motor Stop
Hold until the motors stop
WARNING: Stopping the motors while
the quadcopter is still in fl ight will cause
a
b
a
c
b
d
c
e
a
d
f
b
e
c
f
d
e