Armytek Optoelectronics Partner A1 Manual do utilizador - Página 2

Procurar online ou descarregar pdf Manual do utilizador para Lanterna Armytek Optoelectronics Partner A1. Armytek Optoelectronics Partner A1 2 páginas.
Também para Armytek Optoelectronics Partner A1: Manual do utilizador (2 páginas)

Imprimir página

Set description

Partner

Items included in the package:

1 - Flashlight

5 - Lanyard

2 - Clip

6 - 2 spare O-rings

3 - Spare rubber button

7 - User manual

4 - Holster

Depending on the model, your flashlight can inconsiderably differ from the pictures in the manual.

The producer reserves the right to change the package at his own discretion without modifying this manual.

Initial Service

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable)

can leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries

in, use new and quality batteries, store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least

once a month. If you have noticed any signs of batteries' defects, withdraw them from the flashlight and take out of operation. It is also

recommended to replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

The flashlight has two operational variants:

Turbo – permanently switched light at Turbo mode (activated by click with the head of the flashlight tightened up). It's an easy and

comfortable operational mode for Hunters, especially when the flashlight is used with a remote switch.

Additional – permanently or intermittently switched light at one of the Additional modes at user's choice (activated by click with the

head of the flashlight unscrewed to 1/8). Additional modes: Firefly, Main1, Main2, Main3, Strobe (hidden).

Momentary on

Half Press & Hold (no click)

Release

1/2

OFF

Turbo

Tighten up

Click x1

Additional

Unscrew to 1/8

Click x1

Cycling through Additional modes

Half Press & Release (no click)

Firefly

1/2

Strobe

Main1

Main3

Main2

* If enabled

Adding Strobe to Additional modes

Unscrew & Tighten up x10

x10

Automemorizing. After switching off the last used Mode is memorized for quick 1-click access at next switching on.

Lock-out function. Unscrew the tailcap to 1/4 for the protection from accidental switching on.

Low Battery Indication.

If the brightness is <25% from the nominal value, the LED flashes 2 times ONCE (after 30sec from switching

on). If you are not sure if it flashed or not switch the flashlight off and on: in case the battery is low flashes will repeat. Light output

decreases to Firefly mode at critical level.

Active temperature control (for Partner C2/C4 only). The flashlight can quickly heat up in Turbo mode. When the temperature becomes

+60°C – the brightness decreases by small steps. After cooling-down (provided that battery voltage is sufficient) the brightness

increases to the Turbo mode again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In

conditions of good air-cooling the flashlight delivers light without stepping down even in Turbo mode. There are no preset timers for

stepping, but real-time active temperature measurements.

Operation

Momentary on.

Any mode switched on by half-pressing of the button and

active till the button is released. In Turbo mode suitable for

giving signals by short button pressings. In Additional mode

quick half-pressings can be used to switch modes.

Turbo.

Tighten the head of the flashlight if it is unscrewed. First full

click of the button turns the light on. Second full click turns it

off.

Additional modes (Firefly + 3 Main + Strobe (if enabled)).

If the head of the flashlight is tightened up, unscrew it for 1/8

of a circle. Full click of the button turns the light on at the last

used Additional mode.

Cycling through Additional modes.

To switch the mode turn the flashlight off and on (by full click

or half-pressing). The modes switch cyclically: Firefly - Main1

- Main2 - Main3 - Strobe (if enabled).

Adding Strobe to Additional modes.

Strobe is a hidden mode which you can add or remove from

the additional modes at your choice. To enable (remove)

Strobe: when the flashlight is ON unscrew and tighten up the

head of the flashlight at least 10 times (while rotation you will

change the modes). The pause must be <1 sec.