ARO 8365 Manual de Instruções - Página 3
Procurar online ou descarregar pdf Manual de Instruções para Perfurar ARO 8365. ARO 8365 16 páginas. Super par-a-mat self-feed drills
SET-UP PROCEDURE WITH OPTIONAL
M105
HYDRAULIC CHECK
20
Assemble hydraulic check to mounting bracket and assemble
mounting bracket to tool using washers (30997) and cap screws
(Y157-44).
.
Measure distance from drill paint to work piece - distance "Y".
Distance "X" between hydraulic check plunger and trip bracket
l
must be less than distance "Y" to prevent damage to drill point
when it approaches the work piece.
Loosen the Cap screws (Yl57-44) and position hydraulic check
to obtain correct setting for distance "X".
Tighten cap screws (Y157-44) securely before operating unit.
Increase the air flow thru the feed control valve marked "F" by
l
Opening two (2) full turns from closed position. This will allow drill
to advance rapidly until the trip bracket contacts plunger of hydraul-
ic check.
.
The hydraulic feed rate adjustment is located at the nameplate
end of the hydraulic check, Rotate extended spindle until the slot
on the spindle is located midway between the highest and the
lowest settings.
Start drill unit and the drill will advance at a rapid rate until the
trip bracket contacts plunger of hydraulic check.
Slowly rotate the hydraulic feed rate counterclockwise for faster
feed rate or clockwise for slower feed rate.
TO CONTROL BREAKTHROUGH
Position hydraulic check so the distance between the plunger and
the trip bracket (distance "X") is less than the distance from the
drill point to the opposite side of the work piece (distance "W").
Set-up of the self-feed drill unit will be the same as explained in
Set-up Procedure, page 1.
ADJUSTMENT SCREW "B"-,
AJUSTMENT SCREW "A"-
l
MOUNTING BRACKET 40316
SCREW
(2) Y157-44
l
ADJUSTMENT,
FEED RATE
HYDRAULIC CHECK (SEE TABLE)-
SEE PAGE 11 FOR HYDRAULIC CHECK DIMENSIONAL DATA.
PARTS INDICATED BY ASTERISK (•) ARE INCLUDED
IN 40591-( ) HYDRAULIC CHECK ASSEMBLY.
Never apply excessive pressure by a holding device which may
cause distortion of a part.
Apply pressure evenly to parts which have a press fit.
Apply even pressure to the bearing race that will be press fitted
to the mating part.
Use correct tools and fixtures when servicing this tool,
Don't damage "0" rings when servicing tool,
Use only genuine ARO replacement parts for this tool, When or-
dering, specify part number, description, tool model number and
serial. number.
motor housing (50) from the outer sleeve (40).
Using wrenches on flats of ring gear (90) and motor housing, un-
-thread
gearing from motor housing.
Pull spindle (89) and components from ring gear.
Remove bearing (87) and spacer (88).
Turn snap rings (68 and 74) so the open portion will allow the
removal of shafts and gears.
Remove lock nut (93), releasing bearings (92) and spindle (91).
.
.
.
.
.
.
-
GEARING DISASSEMBLY
Remove chuck from gearing.
-
Thread adjustment screws (6 and 7) all the way back and push
- the piston rod (47) all the way forward to expose wrench flats of
motor housing (50) from the outer sleeve (40).
- Using wrenches on flats of housing adapter and motor housing,
unthread gearing from motor housing.
If tool has double gearing, unthread lock nut (82) from housing
- adapter (67).
Remove spindle nut (85) from spindle.
_ DIRECT DRIVE MODELS: Unthread and remove Collet nut (116) and
bearing lock nut (114).
GEARING ASSEMBLY
Lubricate gears and needle bearings (70) liberally with ARO
33153 grease and assemble two needle bearings to each
gear.
Assemble one gear to spindle and secure with shaft (71).
Repeat for opposite shaft and gear.
Rotate snap ring, securing both shafts.
Pack bearing (78) with ARO 33153 grease and assemble
bearings (78 and 79) to spindle. NOTE: Bearing (78) is an an-
gular contact type bearing and should be installed with the
identification markings facing away from the spindle.
Assemble washer (81), wavy washers (80) and spindle into
lock nut (82).
Assemble seal (83), nose housing (84) and spindle nut (85) to
gearing.
. ,
DIRECT DRIVE MODELS: Assemble bearing lock nut (114) to
spindle.
Assemble gearing to tool.
Assemble chuck to spindle.
_ Grasp lock nut (82) in one hand and tap the threaded end of the
spindle with a soft faced hammer; spindle and components will
loosen from lock nut.
Remove bearings (78 and 79) and turn snap ring so the open por-
- tion will allow the removal of one shaft, releasing gear. Repeat
for removal of opposite shaft and gear,
48129-1 GEARING DISASSEMBLY
Remove chuck from gearing.
_ Thread adjustment screws (6 and 7) all the way back and push
the piston rod (47) all the way forward to expose wrench flats of
48129-1 GEARING ASSEMBLY
Pack bearings (92) with ARO 33153 grease and assemble to spin-
3
-