Alto Wap TitanPlus Manual de Instruções - Página 13

Procurar online ou descarregar pdf Manual de Instruções para Máquina de lavar roupa de pressão Alto Wap TitanPlus. Alto Wap TitanPlus 19 páginas.

Imprimir página

SC 710 W only:

• Turn rotary knob on the safety

control block to maximum

pressure (Fig. 9).

SC 710 W only:

• Turn FlexoPowerJet nozzle in

direction CHEM up to the

stop (Fig. 12).

• Spray the object to be clea-

ned.

• Allow the cleaning agent to

work, depending on the

degree of soiling, then rinse

off with the high-pressure

spray jet.

The cleaning agent must not

be allowed to dry on the

surface!

FINISHING OPERATION AND

STORAGE

• Turn the metering valve to

position

• Turn the operating mode switch

to position

•

Allow the machine to run for

approx. 1 minute, then turn the

operating mode switch to

position OFF.

• Actuate the trigger gun until the

machine is completely depressu-

rised.

• Insert the safety lock (Fig. 8/1).

• Turn off the water tap.

• Pull the machine plug out of the

plug socket and coil up the

mains cable.

• Disconnect the water hose from

the machine.

• Store the machine in a frost-

proof room where it is safe from

unauthorised use.

If the machine cannot be stored in a

frost-proof room, proceed as follows:

• Turn off the water tap.

• Turn the operating mode switch

to position

and actuate

the trigger gun

•

Gradually pour antifreeze

(approx. 5 litres) into the water

tank.

• The machine is protected against

frost when antifreeze solution

emerges from the nozzle of the

spray lance.

•

When the machine is put into

service again, the antifreeze

solution can be collected and

stored for future use.

Option / model variants

SERVICE AND MAINTENANCE

The maintenance operations

marked with

should only be

carried out by the Wap service

technician.

MAINTENANCE SCHEDULE

Weekly or every 40 opera-

ting hours

• Check the oil level

Every 3 months or every

200 operating hours

• Change the pump oil

• Pump system

• Flame sensor

Annually or every 500

operating hours

• Heat exchanger and

ignition system

• Fuel system

As required

• Grease the manual

screw fittings on the

spray lance and high-

pressure hose

• Descale the system

OIL LEVEL CHECK / OIL

CHANGE

Check the oil level in the high-

pressure pump regularly at the

dipstick of the oil filler plug.

• Top up with oil when required.

• If the oil has a grey or white

shade, change the oil.

Unscrew the oil drain plug on

the pump housing and

dispose of the old oil in

accordance with the disposal

regulations.

• Renew the drain plug gasket

and screw in the plug again.

• Fill with oil and close the oil

filler plug.

Oil grade: SAE 15 W 40 engine oil

Oil capacity: DX 0.4 l

SC 0.33 l

PUMP SYSTEM

• Clean the screens and filter in

the water inlet line (float

SC 710 W / SC 740 W / SC 780

DX 840 W / DX 860 / DX 900 / DX 980 / TitanPlus

valve, high-pressure pump

inlet).

• Grease the manual screw

fittings on the spray lance and

high-pressure hose.

FLAME SENSOR

• Remove the sensor and clean

with a soft cloth.

• Ensure that the sensor is

correctly seated when instal-

ling again.

HEAT EXCHANGER AND

IGNITION SYSTEM

• Have cleaning carried out by

the Wap service technician,

see "Maintenance schedule".

FUEL SYSTEM

• Empty the fuel tank. Clean

the tank and fuel lines.

• Dispose of the cleaning fluid

in accordance with the

disposal regulations.

SETTING OF THE WAP

AUTOMATIC SCALE ALARM

SYSTEM

The automatic scale alarm

system is set at the factory to

water hardness class 2. Should

an adjustment be necessary,

proceed as follows:

• Measure the water hardness

or ask your water supply

company.

• Set the number of drops per

minute (see table) at the

metering device (Fig. 13).

Hardness

°dH

Drops/min.

class

1 soft

0-7

medium-

7-14

hard

3 hard

1 4 - 2 1

4 very hard

>21

1°dH = 1,25°e = 1,79°f

DESCALING

CAUTION!

Descaling agents cause burns.

Avoid contact with the skin,

eyes and clothes. Wear appro-