Altrad FEND-H05-MCH Instruções originais, instruções de segurança, peças sobressalentes - Página 10

Procurar online ou descarregar pdf Instruções originais, instruções de segurança, peças sobressalentes para Cortador de lenha Altrad FEND-H05-MCH. Altrad FEND-H05-MCH 20 páginas.

Imprimir página
Metal parts (nails, wire etc.) must be removed from logs
before splitting.
Every other form of use is considered improper use. The
manufacturer accepts no liability for any damages resulting
from improper use, and any risk is in this case borne solely by
the user.
R
e
s
i
R
e
s
i
Even if used properly, residual risks can exist even if the
relevant safety regulations are complied with due to the design
determined by the intended purpose.
Residual risks can be minimised if the "Safety information" and
the "Intended usage" as well as the whole of the operating
instructions are observed.
Observing these instructions, and taking proper care, will reduce
the risk of personal injury or damage to the equipment.
Failure to observe the safety precautions can lead to injury to
the operator or damage to property.
Risk from electricity, by using non-standard electrical
connections.
Touching live parts of opened electrical components.
Risk of fire and slipping by leaking hydraulic fluid.
In addition, in spite of all the precautionary measures taken, non-
obvious residual risks can still exist.
S
a
f
e
S
a
f
e
Before commissioning this product, read and keep to
the following advice. Also observe the preventive regulations
of your professional association and the safety provisions
applicable in the respective country, in order to protect
yourself and others from possible injury.
Pass the safety instructions on to all persons who work
with the machine.
Keep these safety instructions in a safe place.
Make yourself familiar with the equipment before using it, by
reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see "Normal
intended use" and "Working with the log splitter").
Ensure that you have stand in a secure standing position
and maintain your balance at all times.
Take a working position, which is behind the slide of the
area of the operating lever. Never stand in the splitting
wedge's zone.
Never stand on top of the machine.
Pay attention at all times. Take care with what you are doing,
and approach the work sensibly. Do not use the machine:
− when you are tired.
− under the influence of drugs, alcohol or medications that
may impair your powers of judgement.
When working with the machine, always wear
− protective goggles or face mask
− safety gloves
− ear protection, if necessary
d
u
a
l
r
i
s
k
s
d
u
a
l
r
i
s
k
s
w
o
r
k
i
n
g
w
o
r
k
i
n
g
− safety shoes with steel toe-caps
Wear suitable work clothing:
− do not wear any loose-fitting clothing or jewellery, since
these may be caught or trapped by moving parts
Within his area of work the operator is responsible for third
parties.
The machine may not be operated by children or young
people under the age of 18.
Keep children away form machine.
Never operate the machine if other persons are in the
immediate vicinity.
Never leave the saw unattended.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Faulty or damaged parts in the device must be replaced
immediately.
Do not spray machine with water
(this is hazardous due to live components).
Do not leave the machine standing in the rain or use when
raining.
Store the unused machine in a dry locked place away from
the reach of children.
Switch the machine off and remove the mains plug from the
socket when
− carrying out repair works
− carrying out servicing and repair works,
removal of faults
− Transporting
− leaving unattended (even during short interruptions)
Check the machine for possible damage
Before continuing to use the machine, the protective
−
devices must be inspected to ensure that they work
perfectly and with their intended function
Check whether the parts are damaged. All parts must be
−
correctly installed and fulfil all conditions to ensure perfect
operation of the saw
Damaged guards and parts must be properly repaired or
−
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible safety warning labels should be
−
replaced immediately.
Electrical safety
Electrical connections must conform to IEC 60245 (H 07
RN-F) with a cable cross-section of at least
⇒ 1.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over 10
m in length. Longer power supply cables will cause a drop in
voltage. The motor will not be able to provide its maximum
performance and the operation of the machine will be
impaired.
When laying the connecting attachments, be sure that they
do get crushed or bent, and that the plug-and-socket
connection does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
1