dji Matrice 210 V2 Manual do utilizador - Página 3

Procurar online ou descarregar pdf Manual do utilizador para Drones dji Matrice 210 V2. dji Matrice 210 V2 12 páginas. Manifold 2 mounting bracket
Também para dji Matrice 210 V2: Manual do utilizador (6 páginas)

Imprimir página

Disclaimer

Congratulations on purchasing your new DJI

affects your safety and your legal rights and responsibilities. Read this entire document

carefully to ensure proper configuration before use. Failure to read and follow instructions and

warnings in this document may result in serious injury to yourself or others, damage to your

DJI product, or damage to other objects in the vicinity. This document and all other collateral

documents are subject to change at the sole discretion of DJI.

By using this product, you hereby signify that you have read this disclaimer and warning

carefully and that you understand and agree to abide by the terms and conditions herein. You

agree that you are solely responsible for your own conduct while using this product, and for

any consequences thereof. You agree to use this product only for purposes that are proper

and in accordance with all applicable laws, rules, and regulations, and all terms, precautions,

practices, policies and guidelines DJI has made and may make available.

Introduction

Mount the MANIFOLD

or Matrice 210 RTK aircraft using the mounting bracket and then connect the cables. The

descriptions below use the M210 V2 and M210 RTK V2 as an example.

In the Box

Mounting Bracket Set × 1

Type A Screw (M2.5×8, Hex) × 10

Type B Screw (M1.6×4, Philips) × 4

Type C Screw (M2.5×14, Hex) × 4

Usage

1. As shown in figure I, assemble the body of the mounting bracket, then tighten the six type A

screws.

2. As shown in figure II, mount the L-shaped blocks to the Manifold 2, then tighten the four type

A screws.

3. As shown in figure III, mount the Manifold 2 and mounting bracket to the upper cover of the

aircraft, then tighten the four type B screws and four type C screws. Make sure to install

them in the direction shown in the figure. DO NOT reverse any item.

4. As shown in figure IV, connect the USB 3.0 port (Type A) on the Manifold 2 to the USB port

at the rear of the aircraft using the USB cable (with 2 Type A ports), connect the power port

on the Manifold 2 to the extended power port at the rear of the aircraft using the XT30 power

cable, and then put the cables into the cable clip on the mounting bracket.

5. Connect the expansion port 3 at the rear of the aircraft to the USB 3.0 port (Type A) or UART

port on the Manifold 2 using an appropriate cable. Refer to the Manifold 2 User Guide for

details. (https://www.dji.com/manifold-2 )

6. When using the Manifold 2, slide the USB mode switch at the rear of the aircraft to the right

Make sure that the cables do NOT obstruct the Upward Infrared Sensor on the top of

the aircraft.

When using with the M210 V2 aircraft, a GPS Kit is required. Refer to the GPS Kit

document for details.

When using with the M210 RTK V2 aircraft, arrange the D-RTK antenna cables

properly to prevent them from being bent excessively when the mounting bracket is

mounted.

Please refer to http://www.dji.com/service for after-sales service for your product where applicable.

DJI shall mean SZ DJI TECHNOLOGY CO., LTD. and/or its affiliated companies where applicable.

2 to the MATRICE

product. The information in this document

210 V2, Matrice 210 RTK V2, Matrice 210,

L-shaped Wrench × 1

USB Cable (with 2 Type A Ports) × 1

XT30 Power Cable × 1