AIMS Power SCC10APWM Manual de instalação e operação - Página 2

Procurar online ou descarregar pdf Manual de instalação e operação para Inversor AIMS Power SCC10APWM. AIMS Power SCC10APWM 2 páginas. Solar charge controller

AIMS Power SCC10APWM Manual de instalação e operação
3.3.7 Accumulative sum of recharged Ah
Displays the accumulative sum of recharged Ah from solar panel. Press the
button
for 5 seconds to reset the meter to 0. Even when the battery is
disconnected the value remains. When 9999Ah are reached, it will switch back
to 0 Ah.
3.3.8 DC load consumption
Displays the accumulative sum of Ah drawn by the DC load.
Press the button
for 5 seconds to reset the meter to 0. Even when
battery is disconnected the value remains. When 9999Ah are reached, it will
switch back to 0 Ah.
3.3.9 High voltage disconnection (HVD) Float voltage - ADJUSTABLE
Displays the float voltage, when battery voltage reaches float voltage, the
controller will start PWM control to keep the battery voltage at same level.
Press the button
(>5 seconds, numbers start flashing) to enter the
setting, then press the
or
to select the setting. Press the button
again to exit the setting (numbers stop flashing).
3.3.10 Low voltage reconnection (LVR) - ADJUSTABLE
Displays the values for the LVR voltage. Under the LVD protection in the
controller, when battery voltage is restored to higher voltage than LVR voltage,
the controller will re-connect the load circuit.
Press the button
(>5 seconds, numbers start flashing) to enter the
setting, then press the
or
to select the setting. Press the button
again to exit the setting (numbers stop flashing).
3.3.12 DC Load operating mode - ADJUSTABLE
As shown on the right, it displays the load operating mode. Different values
represent different working modes.
24h - normal mode, there is always output unless the battery voltage is too
low.
1-23h - light control with time control mode. Load will turn on after dusk
and turn off according to the timer setting.
0h - light control mode, load will turn on after dusk and turn on before
dawn.
Press on the button
(>5 seconds, numbers start flashing) to enter the
setting, then press the
or
again (>5 secs) to exit the setting (numbers stop flashing).
4. COMMON FAULT AND HANDLING
4.1 LVD Protection resolution
Screen display as shown in the figure that the battery drops below the LVD
protection voltage. The controller has entered the LCD protection state, load
circuit has been disconnected. Use the solar panels to recharge the battery or
charger when the battery voltage reaches LVR voltage, the controller will
resume the load power supply after battery reaches normal working state.
4.2 Over load Protection fault resolution
Screen display (see the figure) and flashing shows over load circuit current
For 60 seconds at more than 1.5 times the rated current.
Overload protection state. After reducing the load, press the button
to restore power to the load.
4.3 Short Circuit Protection fault resolution
Screen display (see the figure on the right) and flashing shows there is a short
circuit on the load circuit. The controller has entered into Short Circuit
Protection State. Check the load for damage to the wiring circuit.
After troubleshooting and correcting short circuit quick press
to enable the load.
4.4 Solar Panel Fault resolution
Symbol flashing indicates that the controller has not detected the solar panels within 24hours. Check
connection from solar panel to charge controller. Also, check if there is an open circuit between solar
panel with controller.
4.5 Load Shock Fault
Open load if the
flashing, this indicate the load current is more than twice rated current of the
controller. This will cause the controller to reset several times.
to select the setting. Press the button
button
5. WARRANTY
AIMS Power offers a 2 year limited warranty.
The following cases are not covered under warranty.
1. DC reverse polarity
The charger is NOT designed with DC reverse polarity protection. A reverse polarity may severely damage the inverter.
2. Incorrect DC wiring
3. Operation in a moist environment
AIMS Power Warranty Instructions:
This product is designed using the most modern digital technology and under very strict quality control and testing guide
lines. If, however you feel this product is not performing as it should, please contact us: [email protected] or
(775)359-6703.
We will do our best to resolve your concerns. If the product needs repair or replacement, make sure to keep your
receipt/invoice, as that will need to be sent back along with the package and RA# prepaid to AIMS. You have a limited 2
year from date of purchase warranty.
This warranty is valid worldwide with the exception that freight and duty charges incurred outside the contiguous 48 United
States will be prepaid by customer.
Except as provided above, AIMS makes no warranty of any kind, express or implied, including without limitation the implied
warranties of merchantability and fitness for a particular purpose. In no event shall AIMS be liable for indirect, special or
consequential damages. This warranty only applies to AIMS Power branded products. All other name brand products are
warranted by and according to their respective manufacturer. Please do not attempt to return non-AIMS Power branded
products to AIMS Power.
For additional products such as:
-
Modified sine wave inverters
-
Pure sine wave inverters
-
Solar charge controllers
-
Generators
-
Inverter chargers with automatic transfer switches
-
Custom cut cables
-
Batteries
-
Solar panels
Please visit our web site:
www.aimscorp.net
To find out where to buy any of our products, you may also e-mail:[email protected] or call (775)359-6703.
6. TECHNICAL DATASHEET
Model
Rated current
Rated voltage
Max solar voltage
Low voltage disconnect
Low voltage reconnect
Float charge
Standby loss
Material
USB output
Charging mode
Temp compensation
Operating condition
Size/Weight
SCC10A PWM
10A
12/24V
<50V(12/24V)
10.7/21.4V
12.6/25.2V
13.7/27.4V
<30mA
ABS+Aluminum
5V/2A
PWM
-4mV/Cell/℃
-20℃ to 60℃ | -4°F to 140°F
6.5L"* 3.5W"* 1.5H"
.5 lb