dji RONIN-M Manual de início rápido - Página 2

Procurar online ou descarregar pdf Manual de início rápido para Drones dji RONIN-M. dji RONIN-M 2 páginas.

Imprimir página

RONIN-M

Quick Start Guide

Start

A. Download and install the DJI Assistant app.

Search "DJI Assistant" on the App Store and then follow the instructions

for iOS installation.

B. Before you start using your Ronin-M, be sure to charge the DJI Intelligent

Battery first.

Pressing the Intelligent Battery power button once will display the current

battery level. Pressing the Intelligent Battery power button and holding

for 1 second will power on the Ronin-M.

C. To check remote control battery level, slide the power switch to the right

to power on the remote control. The battery level indicators display the

current battery status. If the low voltage alert sounds, please recharge

the battery via the micro USB charging port.

Refer to the User Manual for more DJI Intelligent Battery information.

●

Use a mobile device that runs iOS 6.1 or above. Android version on the way.

●

Assembling the Ronin-M

A. Deploy the tuning stand as shown.

B. Assembling the handle bar.

Press the buttons

on the outsides of the lower

Attach the handle bars to both sides of the

legs and rotate the legs downward, away from

top handle and tighten the grip screws.

the stand. Then press the buttons

on the

Attach the grips to the handle bar and

outsides of the upper support arms and pull

lock them in the preferred position.

them upward, away from the stand. Press the

Place the handle assembly on the tuning

button

on the vertical support and slide it up

stand.

to extend the stand.

C. Attach the Ronin-M to the handle.

D. To mount the DJI Intelligent Battery into

the Ronin-M, loosen the thumb screws

Slide the handle bar horizontally into the

on either side of the battery and slide it

gimbal and tighten the lock-knob.

directly into the gimbal and then slide

down. Tighten the thumb screws. Ensure

the battery is seated all the way down.

Make sure the battery is powered off during the installation process.

●

Mounting the Camera on the Mounting Plate

A. Attach the camera to the mounting plate and tighten the screws.

B. Attach the lens support to the mounting plate.

C. Apply upward pressure to the lens support and tighten the screw.

Mounting the Camera on the Ronin-M

Insert the camera until the safety lock engages. Make sure the camera first achieves a rough balance

by sliding the camera platform forward and back. The camera should not tilt forward (lens heavy) or

tilt backward. When you have arrived at a rough balance, tighten the side clamp.

DJI Assistant

Remote Control Battery

Level Indicators

25% 50% 75% 100%

The camera needs to be fully setup with all accessories prior to installing and balancing on the gimbal.

●

Balancing

A. Balancing the Vertical Tilt

Rotate the tilt axis so that the camera

lens is pointing upward and loosen the

two vertical adjustment tabs. Gently

slide the camera mount crossbar forwards

or backwards until the camera points

upwards when released. Latch the tabs

back into their closed position to tighten.

C. Balancing Depth for the Tilt Axis

Loosen the side clamp to slide the camera

forwards or backwards until the tilt axis

remains level and then tighten the side

clamp.

Pairing with the DJI Ronin-M Assistant App

A. Power on the Ronin-M. Switch on Bluetooth on your mobile device and launch the DJI Assistant app.

B. Connect your mobile device to the Ronin-M within the DJI Assistant app.

C. When using the app for the first time, you will be prompted to register using a valid e-mail address.

D. Check balance in the Viewer page. If a particular motor axis indicates a power greater than 10,

please rebalance the camera.

B. Balancing the Roll Axis

Loosen the two lock-knobs to slide the

camera left or right until the roll axis remains

level, and then tighten the two lock-knobs.

D. Balancing the Pan Axis

Open the clamp

on the pan axis and turn

the knob

to slide the assembly. Tighten

the clamp

after balancing is completed.

Viewer

？

Power

Angle

Pan Axis

1.89

。

-2

-0.45

。

Tilt Axis

-0.01

。

Roll Axis

Power

Angle

Device Selection

Ronin-M: 000036

Voltage

14.50V

Temperature

35.40

。

Time

0:01:59

Gimbal

Control

Viewer

DJI Ronin-M Assistant App Settings

A. With the Ronin-M on the tuning stand and a properly balanced camera, tap the Auto Tune Stability

button.

B. Switch on/off the Briefcase Mode as needed.

C. Switch on/off the SmoothTrack

Mode:N/A

Mode：

N/A

Mode as needed. In the

Gimbal

Motor

Gimbal

SmoothTrack

？

SmoothTrack Mode

SmoothTrack options menu,

Auto Tune Stability

Briefcase Mode

Pan SmoothTrack

Configuration

Motor Kill

Tilt SmoothTrack

the settings for the pan axis,

Stiffness

Trim

Roll Remote Contuol Off

Roll SmoothTrack

Pan Axis

tilt axis and the roll axis can

Internal Receiver Off

SmoothTrack Adjustments

Tilt Axis

Enable Silent Mode

Speed

be independently adjusted.

Roll Axis

Pan Axis

Calibrate Center

Tilt Axis

Live Data

D. Adjust the control speed.

Calibrate System

Roll Axis

Power

Angle

Restore default settings

Pan

E. If the Ronin-M starts to vibrate,

Test

Tilt

Test Pan Speed

Roll

Accounts

＊＊＊@＊＊＊.com

go into the "Motor" page and

Test Tilt Speed

reduce stiffness settings.

Gimbal

Control

Viewer

Gimbal

Control

Viewer

Gimbal

Control

For more information, please refer to the User Manual.

●

Pairing with PC/MAC Assistant (Alternate Work Flow)

A. Connect the Ronin-M to your computer via USB cable and

be sure the Ronin-M is powered on.

B. Download the PC/MAC Assistant from DJI.com (ensure you

have also installed the DJI Windows Driver first if you are

installing it on a Windows Operation System), and then

launch the Assistant.

C. Click the Auto Tune Stability button.

D. Reduce motor stiffness settings if the Ronin-M shakes.

E. Switch on/off the Briefcase Mode and SmoothTrack Mode as

needed. Adjust the maximum control speed.

The tuning abilities of the DJI Assistant app and DJI PC/MAC Assistant are the same. There is no need

●

to repeat your settings in both Assistants.

The DJI Ronin-M Assistant app and the PC/MAC Assistant program cannot be simultaneously launched

●

and connected at the same time. If running the Assistant app on your mobile device, be sure to

disconnect the micro USB cable.

Connecting the Remote Control to Ronin-M

A. Turn on the Ronin-M.

B. Press the recessed Bind Button (shown below) of the Ronin-M once with something sharp such

as a paperclip.

C. Slide the power switch to the right to power on the remote control. If the LED of gimbal turns solid

green light, the remote control and the Ronin-M have been successfully bound.

D. Test the remote control to see if it is paired.

Remote Control Operation

A. MODE:

B. FUNCTION:

The MODE switch is used for toggling

i. The FUNCTION switch is used to select the

SmoothTrack.

SmoothTrack speed.

Position 1

Position 2

-Free, SmoothTrack Off

Position 1

-Fast

-Free, SmoothTrack On

Position 2

ii. Activating Motor Kill Switch by quickly

flipping the FUNCTION switch up and down

Position 3

-Reset to Center, SmoothTrack On

3 times. This will enable/disable Motor Kill.

C. Left Stick: Horizontal movements on the left stick

control the roll axis.

D. Right Stick: Horizontal movements on the right stick

control the pan axis. Vertical movements on the right

stick control the tilt axis.

Control

Maximum Speed

？

Control Speed Adjustment

Pan

Tilt

Thumb

Controller

Remote

Operator

Deadband

Accel

Viewer

Gimbal

Control

Viewer

Auto Tune Stability

Bind Button

Position 3

-Normal

-Slow