Custom Dynamics Road Glide CD-RG-TS-15-B Instruções de instalação
Procurar online ou descarregar pdf Instruções de instalação para Acessórios para motociclos Custom Dynamics Road Glide CD-RG-TS-15-B. Custom Dynamics Road Glide CD-RG-TS-15-B 2 páginas. Led turn signals
Imprimir página
Part Numbers:
CD-RG-TS-15-B
CD-RG-TS-15-C
Package Contents:
- LED Turn Signal Assemblies w/ gaskets (pair)
- 5/16-18 x 3/4 Sock Head Screw (2)
- 1/4-20 x 1 Button Head Screw (2)
- Thread locker 0.5 ml (1)
- Instructions
Fits: 2015-2018 Harley-Davidson® Road Glide®, Road
Glide® Special & Road Glide® Ultra Models Including
CVO™
ATTENTION
Please read all Information below before Installation
Warning:
Disconnect the negative battery cable from battery; refer to
owner's manual. Failure to do so may result in electrical shock, injury or
fire. Secure negative battery cable away from positive side of battery and
all other positive voltage sources on vehicle.
Safety First:
Make sure the bike is parked on a level surface and bike's
mechanical components are cool to the touch.
Notice: This product is designed and intended for use as auxiliary lighting
on motorcycles only. This product is NOT intended to replace any original
equipment lighting installed on the motorcycle and should not be used for
that purpose. This product must be wired such that it does not interfere
with any original equipment lighting.
Note: Some technical knowledge may be needed for this installation.
Consult your vehicle detailed service manual for instructions on removing
the front fairing and for electrical wiring information. Use a meter or test
light to verify the turn signals before connecting to any vehicle wiring. If
the steps contained within are beyond your skillset, do not attempt instal-
lation, contact a qualified mechanic or dealership to assist you.
Cleaning: Take special care in cleaning the finish. Never use abrasive
polishes or cleaners as these can scratch the finish.
Questions? Call us at: 1 (800) 382-1388
Custom Dynamics® Road Glide® LED Turn Signals
We thank you for purchasing the Custom Dynamics® Road Glide®
LED Turn Signals. Our products utilize the latest technology and
highest quality components to ensure you the most reliable ser-
vice. We offer one of the best warranty programs in the industry
and we back our products with excellent customer support. If you
have questions before or during installation of this product please
call Custom Dynamics® at 1(800) 382-1388.
CD-RG-TS-15-RAW
1.
2.
3.
4.
5.
6.
7.
8.
M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
Installation Instructions
Installation:
Remove the 4 stock wind-
shield bolts and remove the
windshield.
Remove factory vent by pull-
ing straight up on the vent.
The vent comes snapped in
place.
Locate and unplug the left
and right side 3 pin turn sig-
nal harness.
Remove the 3/16" socket
allen head bolts from the
outside of each turn signal
housing.
Remove both left and right
speaker grilles on the inner
fairing by prying up with a
small flat head screwdriver
between the speaker grill and
inner fairing.
Once the speaker grilles are
removed, locate and remove
the T-27 torx bolts in each
corner of the speaker hous-
ing.
Locate and remove the two
T-25 screws below each
glove box on the inner fairing
that fasten the wind deflec-
tors and the outer fairing to
the inner fairing.
Once the bolts are removed
the outer fairing will be sepa-
rated from the inner fairing.
Remove the outer fairing
(with OEM turn signal hous-
ings still attached) and set to
the side.
1
3
4
6
7
10-2017