Custom Dynamics TruFlex TF15 Manual de instruções de instalação - Página 2

Procurar online ou descarregar pdf Manual de instruções de instalação para Acessórios para automóveis Custom Dynamics TruFlex TF15. Custom Dynamics TruFlex TF15 6 páginas.

Imprimir página

Installation Instructions - Page 2

ATTENTION

Please read all Information below before Installation

Important: This product is designed and intended

for use as auxiliary lighting only. It is NOT intended

to replace any original equipment lighting installed

on the vehicle and should not be used for that pur-

pose. This product must be wired so that it does not

interfere with any original equipment lighting.

Note: Please read all instructions before beginning

installation. Some wiring knowledge and soldering

experience will be helpful. Consult your vehicle

detailed service manual for wiring information and

color codes. Use a meter or test light to verify wiring

before cutting or tapping any vehicle wiring. If the

steps contained within are beyond your skillset, do

not attempt installation, contact a qualified mechanic

or dealership to assist you.

Safety First: Always wear appropriate safety gear

including safety glasses when performing any elec-

trical work. It is highly recommended that safety

glasses be worn throughout this installation process.

Turn fuel supply valve to the off position before

starting installation. Be sure vehicle is on level sur-

face, secure and cool.

Warning: Disconnect negative battery cable from

battery; refer to owner's manual. Failure do to so

may result in electrical shock, injury, or fire. Secure

negative battery cable away from positive side of

battery and all other positive voltage sources on

vehicle.

Note: TruFLEX® products are very flexible but will

NOT accommodate hard 90 degree angles. Doing

so can cause stress to the board and the LEDs. The

product also does not flex from side-to-side, it must

be installed in a straight line. Damage or failure from

these types of incorrect installation is not covered

under warranty.

Recommendation: To increase the adhesion pow-

er of the 3M mounting tape, it is recommended to

use 3M Adhesion promotor, sold separately.

Note: 3M Adhesion promotor is classified as a sensitive

chemical and cannot ship any carrier by Air or international.

Custom Dynamics may not be able to ship promotor with

orders in these cases. Contact us for details.

Important: It is recommended that the installation of

this product should be performed in a controlled

environment of 65 F or above. Allow 24 hours for

the tape to properly adhere before riding or washing

the bike.

Questions? Call us at: 1 (800) 382-1388

General Product Mounting Instructions

Choose the desired location to mount the LED strip(s).

Clean the surface thoroughly before mounting with appro-

priate cleaning method and rubbing alcohol.

Note: It is recommended to apply 3M adhesion promotor to

the mounting surface to increase tape adhesion, sold sepa-

rately. If 3M Promotor ampule was purchased, open the vile

and apply generously to the mounting surface. Allow 3-4

minutes to dry.

Inspect the vehicle and plan the route the wiring will make

to the connection point. Keep in mind each unit has 36" of

wiring. Consult vehicle detailed service manual for vehicle

wiring information and wire color codes. Use a meter or test

light to verify vehicle wire functions before connecting.

Drill holes if necessary in the mounting surface to allow for

the wiring to pass. Feed the wiring through the holes.

Remove the Red backing from the Tape and carefully

mount in the desired location, paying attention to the de-

sired level and center. Take care in this step as once the

tape adheres to the surface, it will be very hard to remove

and re-apply and is not recommended.

Dress the wiring with shrink tubing (not included) as needed

to protect wiring from sharp metal or openings, then run the

wiring along the chosen route from step 4. Make sure wiring

cannot be accidently cut, pinched, or frayed by moving or

sharp parts. Keep wiring from coming in direct contact with

high heat components.

Once you have reached the chosen connection point, trim

any excess wiring from LED wires the and prepare the wir-

ing ends by stripping back the insulation.

Wiring the Connections

All single color TruFLEX® are a 2 wire power system.

Black is always Ground, which should be connected to a

suitable ground wire in the vehicle's wiring harness or di-

rectly to the Negative [ - ] terminal of the battery. The Col-

ored wire is always the Power [ + ] which should be con-

nected to the vehicle turn, brake, or running light positive

power wire depending on desired application.

All dual color and 2 or 3 section TruFLEX® will have more

wires depending on configuration, but the same color rules

apply. Black is ground and colored wires are positive.

Depending on the type of TruFLEX® you have purchased

(see page 1 for product listing) and which converters pur-

chased, please refer to the corresponding pages for wiring

diagrams and scenarios.

M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

06-2016SM