CustomWorks Dominator Modelo - Página 4

Procurar online ou descarregar pdf Modelo para Carro de brincar motorizado CustomWorks Dominator. CustomWorks Dominator 17 páginas. 1:10 scale 4wd dirt oval car kit

Imprimir página

Bag C

Reduction Assembly

-Parts for

Bag C

3620

Qty 1

Reduction Shaft

-Press (1) 3619 Roll Pin in the hole furthest from the e-clip

groove in the 3620 Reduction Shaft.

-Slide the 3621 Gear Hub onto the Reduction Shaft so it

seats over the Roll Pin, then press the next Roll Pin in the

Reduction Shaft behind the Gear Hub.

-Slide on (1) of he 3622 Reduction Pulleys, then press the

last Roll Pin in the Reduction Shaft.

-Slide the other 3622 Reduction Pulley and retain using the

5009 E-Clip.

-Attach the 4881 Spur Gear to the Gear Hub using the (2)

5252 Screws with 5212 Washers on them. Without the

washer, the screw will not tighten on the spur gear!

Bag D

Chassis

-Parts for

Bag D

3640

Dominator Chassis

3651

3624

1232

3650

3623

5262

3640

Bag E

Drive Carriers/Top Deck

-Parts for

Bag E

3641

Dominator Top Plate

-Press a 1234 Bearing into each of

the (4) 3651 Bearing Cams.

1234

3622

Qty 2

3621

Qty 1

Reduction Pulley

Gear Hub

3650

Qty 1

Motor Plate

-Mount the 3650 Motor Plate to the 3640 Chassis using (2)

5262 Screws.

1232

-Press (1) 1232 Flanged Bearing into the 3650 Motor Plate

and install the Reduction Assembly into the bearing.

-Align the 3624 Rear Belt (SHORT) over the pulley gear

closest to the spur gear. Align the 3623 Front Belt (LONG)

over the outer most pulley.

-Press (1) 1232 Flanged Bearing into the 3651 Reduction

Plate. Align the bearing onto the Reduction Assembly.

-Mount the 3651 Reduction Plate to the Chassis using (2)

5262 Screws.

Qty 1

3654 Qty 4

3655

Drive Carrier

Bearing Cam

- Attach each bearing cam to a 3650 Drive Carrier using (2) 8046 Screws.

- Make (1) of each part shown below.

- NOTE: The bearing cam has a "thick" and "thin" side, thick side ALWAYS facing Down!

"THIN SIDE"

3655

Left Front

"THICK SIDE"

5009

4881

Qty 1

3mm E-Clip

81T 48P Spur Gear

4881

5212

5252

3651

Qty 1

1232

Reduction Plate

4x8mm Flanged Bearing

1234

Qty 4

5263

Qty 4

15X10mm Bearing

4-40 x 3/8 FH Screw

Left Rear

1:1

5252

Qty 2

4-40 x 1/4 BH Screw

3619

3620

3621

Qty 2

3623

Qty 1

3624

Front Belt

Rear Belt

3624

1:1

5252

Qty 8

8046

4-40 x 1/4 BH Screw

2-56 x 1/4 BH Screw

Right Front

5212

Qty 2

3619

Qty 3

Washer

Roll Pin

3622

5009

1:1

Qty 1

5262

Qty 4

4-40 x 1/4 FH Screw

3651

1:1

Qty 8

5282

Qty 2

4-40 x 3/8 HOLE HEAD

Right Rear