Dodge Quantis MSM/RHB 88 Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Equipamento industrial Dodge Quantis MSM/RHB 88. Dodge Quantis MSM/RHB 88 2 páginas. Reducer

Imprimir página
Dodge Quantis MSM/RHB 88 Manual de instruções
7.
Turn reducer upright or on its side. Use caution not to damage
either type of seals and install drive shaft through the adapter
housing into the reducer. Line up the keyway in the drive shaft
with the keyway in the reducer hub bore. Slide or gently tap
key into reducer through the input shaft side of the output
hub.
8.
Install the retaining ring (411) into the snap ring groove. Install
keeper plate (402) flush against retaining ring.
9.
Install spring washer (406) and retaining bolt (405) making
sure the drive shaft is fully seated into the reducer. Tighten
the retaining bolt to the tightening torque specified in Table 2.
Install dust cap (401).
Table 2–Tightening Torques for Retaining Bolt
Unit Size
Bolt Thread Size
MSM/RHB 38
3/8-16
MSM/RHB 48
3/8-16
MSM/RHB 68
5/8-11
MSM/RHB 88
3/4-10
MSM/RHB 108
3/4-10
MSM/RHB 128
3/4-10
DRIVE SHAFT REMOVAL
To remove the drive shaft from the reducer, the following steps
are required. Reference Figure 2 for disassembly arrangement.
A
B
Figure 2 - Screw Conveyor Diassembly
1.
Remove the dust cap (401), the driveshaft retaining bolt
(405) and lock washer (406), the keeper plate (401) and the
retaining ring (411).
2.
For ease of disassembly, it is recommended that the following
tools be made and used as described: (A) round keyed nut,
dimensions in Table 3, (B) removal bolt, dimensions in Table
4.
3.
The round keyed nut (A) is inserted into the free space
between the retaining ring in the gear unit's hollow shaft and
the end of the machine's drive shaft.
4.
The removal bolt (B) is screwed into the nut (A) which
presses a disk (C) against the screw conveyor drive shaft.
The resulting force pushes the gearbox off of the drive shaft.
5.
The driveshaft can now be easily removed from the reducer
by pulling the driveshaft straight out.
Dodge Industrial, Inc.
1061 Holland Road
Simpsonville, SC 29681
+1 864 297 4800
© DODGE INDUSTRIAL, INC.
AN RBC BEARINGS COMPANY
Torque
248 in-lb
248 in-lb
611 in-lb
1221 in-lb
1221 in-lb
1221 in-lb
C
M1
REMOVAL BOLT
Table 3–Removal Bolt Dimensions
Unit Size
M1
MSM/RHB 38
3/8-16
MSM/RHB 48
5/8-18
MSM/RHB 68
3/4-10
MSM/RHB 88
7/8-14
MSM/RHB 108
7/8-14
MSM/RHB 128
7/8-14
Note: The retaining bolt supplied with the gear unit cannot be used for the
purpose of disassembly and must be replaced by the bolt in Table 3. The round
keyed nut and disk should be made from 1045 steel and the removal bolt should
be a minimum of SAE Grade 5.
Y
ØFH
UY
ØUE
ROUND KEYED NUT
Table 4–Removal Rounded Key Nut and Disk Dimensions
Unit Size
Y Max
MSM/RHB 38
0.250
MSM/RHB 48
0.312
MSM/RHB 68
0.375
MSM/RHB 88
0.500
MSM/RHB 108
0.625
MSM/RHB 128
0.625
VB1
S
VB1
6.00
7.00
8.00
9.50
12.50
14.00
FG
M1-TAP
FV
DISK
UY Max
ØUE
1.367
1.245
1.52
1.370
1.669
1.495
2.22
1.995
2.65
2.370
3.03
2.745
*16007-0722*
All Rights Reserved. Printed in USA.
MN16007 07/22
S
0.31
0.5
0.63
0.81
0.81
0.81
ØUE
GF
GF
0.12
0.12
0.25
0.25
0.31
0.31