Dodge SLEEVOIL RTL 10 Manual de instruções - Página 9
Procurar online ou descarregar pdf Manual de instruções para Equipamento industrial Dodge SLEEVOIL RTL 10. Dodge SLEEVOIL RTL 10 12 páginas. Pillow blocks
Imprimir página
Oil Maintenance Schedule
Drain, flush, and refill with oil after 2 to 3 weeks of initial break-
in operation. Since the satisfactory operation of the bearing
depends entirely on an oil film being maintained between the
shaft and the bearing liner surface, it is recommended that an oil
analysis be performed at these regular intervals.
•
Every 3 months for 24 hour/day service
•
Every 6 months for 8 hour/day service
Acceptably of oil should be referred to the lubricant manufacturer.
If oil quality is acceptable then repeat this procedure in 3 month
intervals. Visually check oil for contamination between oil analysis
checks. Oil service life depends upon several factors such as
ambient conditions, operating temperature and frequency of
bearing starts and stops. It is recommended that the oil be
changed at least once per year for unfiltered static applications.
Removing contaminants through the use of either the OLF 2
(Oil Level and Filtration 2) Unit or a circulating oil system can
extend oil service life. Consult equipment manufacturer for more
information.
Any questions about installation, maintenance, and arrangement
of coolant or oil connections should be referred to the equipment
manufacturer.
NOTE: Isolators or Auxiliary Seals are recommended for
outdoor applications, contaminated atmospheres, and high
volume air flowing over the bearing.
Temperature
The bearing temperature will increase after start-up until its
normal operating point is reached. The normal operating
temperature should not exceed 180°F. Make sure to check
with the OEM for the specified normal operating temperature.
An alarm temperature should be set at 15°F above the normal
operating temperature. A shut-down temperature should be
set at 30°F above the normal operating temperature. Some
fluctuation due to ambient temperature change is normal.
Low ambient and operating temperatures can be as harmful to
the bearing as high temperatures. The Dodge heater / thermostat
combo can be used in these low ambient conditions.
The Dodge heater / thermostat combo turns on at 70°F and
turn off at 100°F to ensure proper oil sump temperature during
operation.
NOTE: The recommended oil temperature at start-up is 70°F
MINIMUM.
CAUTION: If heaters are used, be sure heaters are off when
oil is removed from bearing.
WARNING: When installing heater and thermoswitch, follow
directions and safety procedures recommended by the
manufacturer. Install wiring in accordance with the National
Electrical Code and local codes. Failure to observe these
guidelines could result in electrical shock.
Vibration
Any significant vibration or imbalance MUST be corrected.
Check with equipment manufacturer for acceptable conditions.
Pillow Block Material Details
Housing:
Liner:
Babbitt:
Oil Rings:
Aluminum Seal:
O-ring:
Aux. Seal:
Grommet:
Grommet Plate:
Pipe Nipple:
Oil Gauge:
Hardware:
Plunger Screw:
Gasket Eliminator:
This Sleevoil pillow block could contain lead in the bearing
Babbitt material, please exercise proper precautions in the use,
installation, dismantling and recycling of this unit.
Other Notes:
CAUTION: This product is not to be used for person moving
applications.
NOTE: Care has been taken to keep instruction manuals
accurate and timely. The most recent version of the
instruction manual can be found on our website:
www.dodgeindustrial.com
Weights:
Table 7 - Weight of RTL Sleevoil
RTL SLEEVOIL
Size
Non-Expansion
Pillow Block
3-7/16
195
3-15/16
238
4-7/16
311
4-15/16
441
5-7/16
521
6
854
7
1018
8
1368
9
1738
10
2262
12
3670
9
Class 30 Gray Cast Iron
Class 30 Gray Cast Iron
Lead or Tin Based Babbitt
Bronze
Sand Cast Aluminum
Elastomer Compound
HNBR with Stainless Steel Retainer
Synthetic Rubber
Carbon Steel
Carbon Steel
Stainless Steel, Polypropylene
Carbon Steel
Carbon Steel
LOCTITE 515 Sealant
Approximate Weights (lbs.)
Expansion
Liner Assembly
Pillow Block
190
230
300
425
500
825
978
1310
1650
2150
3500
47
65
82
113
144
182
257
412
623
955
1405