DogWatch SmartCollar Instruções de utilização

Procurar online ou descarregar pdf Instruções de utilização para Produtos para animais de estimação DogWatch SmartCollar. DogWatch SmartCollar 2 páginas.

Imprimir página

Batteries

Resetting the Low Battery Light

1. Remove the old battery.

2. Before inserting a new battery, let the SmartCollar

sit for five minutes with no battery. (If you forget

to wait prior to inserting a new battery, the "low

battery" light will continue to blink red until it

automatically resets itself after 24 hours.)

3. After five minutes, insert the new battery.

Battery Insertion Instructions

The DogWatch SmartCollar® is powered by a 3.6 volt

lithium battery with a battery life of up to 1 year.

The positive end of the battery must be inserted down.

IMPORTANT: The use of any battery other than a battery authorized by DogWatch Inc.

can cause erratic operation of the SmartCollar and could cause permanent damage.

The use of any unauthorized battery will void the warranty on the SmartCollar.

Setting the Receiver Levels

The Receiver has

7 levels of correction

plus Audible Only.

Your DogWatch Dealer will start the training on the appropriate level according to

your dog's personality and traits. As training continues and your dog adjusts to the

Hidden Fence, the settings may need to be adjusted.

If you need to change the training level on the receiver, hold the magnet on your

Multi-Tool to the training level adjustment location on the side of the receiver (see

right). Hold the magnet steady and you will hear a series of beeps that indicate the

current training level. The training level will begin to advance while the magnet is

held in position. When you reach the desired setting, pull the magnet away from

the receiver.

"Audible Only" = 1 long beep

Level 1 = one short beep

Level 2 = two short beeps

Level 3 = three short beeps, etc.

When the magnet activates the receiver, the number of

beeps indicates the current training level. As long as

the magnet is held in place, it will advance through the

receiver training level settings in the order shown in the

chart on the next page.

Note: Any magnet will activate the receiver.

Features & Settings

Transmitter and Training Level Settings

Receiver

Training

Levels

Audible Only*

(extra low) 1

(low) 2

(low medium) 3

Insert battery

POSITIVE

(medium) 4

end down.

(medium high) 5

(high) 6

(extra high) 7

Example: If the receiver is on Level 1 and the transmitter is on Rate 1, your dog will

receive the lowest level of correction and the least number of pulses per second.

Please, remember that if your Receiver Level is set to 1, 2, or 3 and you switch

the Training Mode to QuickAlert (Mode B), your training setting may change. For

example, if the receiver is set to Level 3 and the transmitter is set to Rate 1, your

dog will receive a slow correction. If you switch your Training Mode to QuickAlert,

your dog will now receive a fast correction.

PROGRAMMING TIPS

Recommended Settings: The majority of dogs respond well to Transmitter Rate

Setting 2 or 3 and a Receiver Training Level 3, 4 or 5. Sensitive or small dogs that

train easily respond best to lower rate settings and lower training levels. If your

dog is not responding to training, your DogWatch Dealer will adjust your system

to a higher training level.

If Your Dog Is Hard To Train: Training Levels 5, 6 and 7 are specifically designed

to meet the needs of hard to train or stubborn dogs. These settings will provide

the extra correction that some dogs need as part of their training.

Multi-Tool

Multiple Dogs: Our receivers allow you to select individual settings for each dog.

This means that one SmartCollar can be set to Audible Only* during training

while another dog is still protected with the correction feature enabled. It is

recommended that the Audible Only* setting be used only during supervised

training sessions.

Never change the Receiver settings when your dog is wearing the SmartCollar.

Use the magnet to set the

training level on the Receiver.

TRANSMITTER MODE AND RATE SETTINGS

Mode A

Mode B

Rate 1

Rate 2

Rate 3

QuickAlert

™

Transmitter Rate Fixed at Medium

Slow

Medium

Fast

Slow

Medium

Fast

Medium

Slow

Medium

Fast

}

Fast

AutoMemory®

will deliver

X-Fast

a correction

equivalent to

XX-Fast

the next level

Audible* and XXX Fast Correction are Simultaneous

upon re-entry.

***Important***

Additional Troubleshooting Tips are available here:

www.dogwatch com/customer-resources

295089 Rev D 12-23

Operating Instructions

DogWatch SmartCollar