DOLD VARIMETER IMD RP 5898 Técnica de controlo - Página 8
Procurar online ou descarregar pdf Técnica de controlo para Monitor DOLD VARIMETER IMD RP 5898. DOLD VARIMETER IMD RP 5898 12 páginas. Insulation monitor
Também para DOLD VARIMETER IMD RP 5898: Tradução das instruções originais (8 páginas), Técnica de controlo (12 páginas), Tradução das instruções originais (17 páginas)
Technical Data
Measuring ciruit L(+)/L(-) to PE1/PE2 (without coupling device)
Nominal voltage U
:
N
Max. voltage range U
:
N
Frequency range:
Max. line capacitance:
Internal resistance (AC / DC): > 90 kΩ
Measuring voltage:
Max. mesured current (R
= 0): < 1.10 mA
E
Response inaccuracy:
Response value hysteresis: Approx. + 25 %; min. + 1 kΩ
On delay
at C
= 1µF,
E
of ∞ to 0.5 * response value:
R
E
Measuring time:
at C
= 1 ... 1000 µF,
E
from ∞ to 1000 kΩ,
R
E
from ∞ to 100 kΩ,
R
E
from ∞ to 1 kΩ:
R
E
Response values
Pre-warning („R
"):
pA
kΩ:
20
30
50
100 250 500 1000 2000
Alarm („R
")
A
kΩ:
1
2
10
20
Each adjustable via rotational switches
Response value broken
wire detection L(+)/L(-):
Response value broken
wire detection PE1/PE2:
Meas. ciruit L1(+)/L2(-) to PE1/PE2 (with coupling device RL / RP 5898)
Nominal voltage U
:
N
Max. max. voltage range U
: AC 0 ... 440 V
N
Frequency range:
Max. line capacitance:
Internal resistance (AC / DC): > 240 kΩ
Meas voltage:
Max. mesured current (R
= 0): < 0.40 mA
E
Response inaccuracy:
Response value hysteresis:
On delay
at C
= 1µF,
E
of ∞ to 0.5 * response value:
R
E
Measuring time:
at C
= 1 ... 1000 µF,
E
from ∞ to 1000 kΩ,
R
E
from ∞ to 100 kΩ,
R
E
from ∞ to 1 kΩ:
R
E
Response values
Pre-warning („R
"):
pA
kΩ:
20
30
50
100 250 500 1000 2000
Alarm („R
")
A
kΩ:
1
2
10
20
Each adjustable via rotational switches
Response value broken
wire detection L1(+)/L2(-):
Response value broken
wire detection PE1/PE2:
Max. wire length
between insulation monitor
and coupling device:
Auxiliary voltage input A1(+)/A2
Nom. Voltage
Voltage range
AC 19 ... 68 V
AC/DC 24 ... 60 V
DC 16 ... 96 V
AC 68 ... 276 V
AC/DC 85 ... 230 V
DC 67 ... 300 V
DC 12 ... 24 V
DC 9.6 ... 30 V
*
W = Permitted residual ripple of auxiliary supply
)
AC / DC 0 ... 230 V
AC 0 ... 250 V
DC 0 ... 300 V
DC or 16 ... 1000 Hz
1000 µF
Approx. ± 90 V
± 15 % ± 1.5 kΩ
IEC 61557-8
< 30 s
See characteristics
50
100 150 250
> Approx. 90 kΩ
> Approx. 0.5 kΩ
RL 5898
RP 5898
AC 0 ... 400 V
AC 0 ... 690 V
DC 0 ... 500 V
DC 0 ... 1000 V
AC 0 ... 760 V
DC 0 ... 550 V
DC 0 ... 1100 V
DC or 16 ... 1000 Hz
1000 µF
Approx. ± 90 V
± 15 % ± 1.5 kΩ
IEC 61557-8
Approx. + 25 %; min. + 1 kΩ
< 30 s
See characteristics
50
100 150 250
> Approx. 500 kΩ
> Approx. 0.5 kΩ
< 0.5 m
Frequency range
45 ... 400 Hz; DC 48 % W*
≤ 5 %
W*
)
45 ... 400 Hz; DC 48 % W*
≤ 5 %
W*
)
≤ 5 %
W*
)
Technical Data
Nominal consumption:
DC 12 V, 24 V, 48 V:
AC 230 V:
Control input X1/X2 for combinied external Test-/Reset-Taste
Current flow:
No-load operation voltage
X1 to X2:
Permissible wire length:
Activation time for test signal: Approx. 1 s
Activation time for reset signal: > 3 s
Outputs
Indicator contact:
Thermal current I
:
th
Switching capacity
to AC 15:
NO contact:
NC contact:
To DC 13:
Electrical life
at 5 A, AC 230 V:
Short circuit strength
max. fuse rating:
Mechanical life:
General Data
Operating mode:
Temperature range
Operation:
Storage:
Altitude:
Clearance and creepage
distances
Rated insulation voltage:
Overvoltage category:
Rated impuls voltage /
pollution degree:
Measuring circuit L(+)/L(-) to
auxiliary voltage A1(+)/A2 and
indicator relay contacts K1, K2 and
trigger output Y1/Y2:
Auxiliary voltage A1(+)/A2 to
indicator relay contacts K1, K2 and
trigger output Y1/Y2:
Indicator relay contact K1 to
indicator relay contacts K2:
Trigger output Y1/Y2 to
indicator relay contacts K1, K2: 4 kV / 2
Insulation test voltage
Routine test:
EMC
Electrostatic discharge (ESD): 8 kV (air)
HF irradiation:
80 MHz ... 1 GHz:
1 GHz ... 2.7 GHz:
Fast transients:
Surge voltage
between
wires for power supply:
Between wire and ground:
HF-wire guided:
Interference suppression:
Degree of protection
Housing:
)
Terminals:
)
Housing:
8
Max. 3 W
Max. 3.5 VA
Approx. 3 mA
Approx. 12 V
< 50 m
2 x 1 changeover contact for Alarm (K1)
and Pre-Alarm (K2)
energized or de-energized on trip
(programmable)
4 A
5 A / AC 230 V
IEC/EN 60947-5-1
2 A / AC 230 V
IEC/EN 60947-5-1
2 A / DC 24 V
IEC/EN 60947-5-1
1 x 10
5
switching cycles
4 A gG / gL
IEC/EN 60947-5-1
50 x 10
6
switching cycles
Continuous operation
- 30 ... + 60 °C
(at range 0 ... - 30 °C limited
function of the LCD displaye)
- 30 ... + 70 °C
≤ 2000 m
IEC 60664-1
300 V
III
IEC 60664-1
4 kV / 2
4 kV / 2
4 kV / 2
AC 2.5 kV; 1 s
IEC/EN 61326-2-4
IEC/EN 61000-4-2
20 V / m
IEC/EN 61000-4-3
10 V / m
IEC/EN 61000-4-3
2 kV
IEC/EN 61000-4-4
1 kV
IEC/EN 61000-4-5
2 kV
IEC/EN 61000-4-5
20 V
IEC/EN 61000-4-6
Limit value classe B
IP 30 (not sealed)
IEC/EN 60529
IP 40 (sealed with
seal wire 50/30)
IEC/EN 60529
The unit must be
disconnected from the
power supply before
the seal is applied
IP 20
IEC/EN 60529
Thermpolastic with V0 behaviour
according to UL subject 94
07.07.23 en / 755A
EN 55011