Asko 1805 FI Manual de instruções de instalação - Página 10

Procurar online ou descarregar pdf Manual de instruções de instalação para Máquina de lavar loiça Asko 1805 FI. Asko 1805 FI 12 páginas.

Imprimir página

Asko 1805 FI Manual de instruções de instalação

FITTING THE

FITTING

THE 1805FI

THE

FITTING

THE

The 1805FI can only be installed with a custom door

panel that extends from the toe kick to the counter top.

The unit comes with everything needed to make

installing the door panel easy. The door is predrilled for

the panel's mounting screws.

The custom panel should be at least 1/4" thick.

ITEMS PRO O O O O VIDED

ITEMS PR

VIDED

ITEMS PR

VIDED

VIDED WITH

Two 3/8" screws (B)

One protective tape (C)

Four adhesive-backed plastic spacer washers (D)

Four 1-3/4" screws (G)

INST

INSTALLING

INST

ALLING

ALLING THE CUST

ALLING

THE CUSTOM P

THE CUST

Before fitting the custom panel, the dishwasher must

be installed underneath the cabinet. After you've made

the required measurements, pull the machine out again

to install the panel.

Refer to the illustration at right for instruction references.

1. Fit the handle (A) onto the panel according to the

manufacturer's instructions. ( NOTE: A handle

should be used rather than a knob, because a knob

does not provide enough grip.)

2. Peel the adhesive backing off the washers and place

them in line with the four keyholes (C) on the metal

front of the dishwasher door.

3. Loosen the screws (D) on the outer edges of the

dishwasher door.

4. Pull the turbo fan exhaust frame (E) down until the

lower edge aligns with the lower edge of the cabinets

and tighten the screws. Next, snap the plastic duct

into the turbo fan exhaust vent.

WARNING!

The custom panel must not

obstruct the turbo fan exhaust.

See step 4 above for instructions

on how to adjust the fan exhaust.

5. The two short screws (B) go into the back of the

panel, 16-3/16" from the upper edge of the panel

and 5/8" from the outer edges. Insert the short

screws into the panel, leaving 1/8" of space between

the screw head and the panel.

6. Hook the panel screws (F) into the keyholes (C) on

the dishwasher door.

7. Push the panel upwards until the lower edge aligns

with the lower edge of the cabinets.

NOTE: The custom panel should not extend more

than 2-15/16" below the bottom of the dishwasher

door. Otherwise, it will strike the toe kick and

damage the machine and/or the panel.

8. Open the door and tighten the screws (F) inside.

9. Remove the backing from the protective tape and

apply it on the bottom edge of the panel, in front of

the exhaust vent.

Page 10

1805FI CUST

1805FI

CUST

CUSTOM DOOR P

OM DOOR P

OM DOOR PANEL

1805FI

CUST

OM DOOR P

WITH

THE UNIT

WITH

WITH THE UNIT

THE UNIT

OM P

OM PANEL

OM P

ANEL

CUST

OM P

ANEL DIMENSIONS

CUST

CUSTOM P

CUST

OM P

OM PANEL DIMENSIONS

ANEL DIMENSIONS

Width:

23-3/8" (597 mm)

Height:

28-1/8"–30-1/8" (714 mm–765 mm)

(Measured from the top of the panel to

the lower edge of the kitchen cabinet.)

Thickness:

1/4" (25 mm)

Weight:

Up to 22 lb.

NOTE: Specifications subject to change without

notice.

NOTE: Heavy-duty door springs can be purchased for

wooden door panels weighing over twelve

pounds. (P/N 8071323-77).

Installing the 1805FI Custom Panel

ADJUSTING THE DOOR SPRINGS

After you install the custom panel,

make sure the door can be

opened at any angle. If it tends to

fall down, pull out the machine

and tension the door springs on

the sides of the machine by

moving them one hole farther

back or by twisting the spring to

make it shorter. If that doesn't resolve the problem, you

may need to purchase the heavy-duty door springs (Part

Number 8071323-77).

FASTENING THE DISHWASHER

TO THE CABINET

Refer to page 8.