Asko 1895 Manual de instruções de instalação - Página 8

Procurar online ou descarregar pdf Manual de instruções de instalação para Máquina de lavar loiça Asko 1895. Asko 1895 12 páginas. User manual use & care guide general fr (french version)
Também para Asko 1895: Manual de início rápido (2 páginas), Manual de utilização e cuidados (12 páginas), Manual de início rápido (2 páginas), (Espanhol) Uso Y Cuidado (12 páginas), (Francês) Manuel D'utilisation Et D'entretien (12 páginas)

Imprimir página

Asko 1895 Manual de instruções de instalação

CONNECTING THE

CONNECTING

In order to prevent heat damage to the inlet valve, all

solder connections must be made before the water

line is connected to the dishwasher.

Flush the water supply line prior to connecting it to the

inlet valve of the machine.

The unit has a float switch in the base pan to protect

against flooding. If the inlet valve connection is not

seated properly, water may leak into the base pan and

activate the float switch. Make sure the connection is

seated and not leaking before completing the installation.

It is important that the water supply line and the shut-off

valve have a sufficient flow volume. At last 3 gallons (12

liters) per minute must be able to pass through the

line. The water pressure should be 18-176 psi.

If the water line is installed properly, there is no need to

seal the connection with Teflon™ tape.

Bend the tube into position after the dishwasher is in

the cabinet opening. It's best to use a tube bender to

keep the line from kinking.

TESTING FOR LEAKS

1. Turn on the water supply and check for leaks.

2. Turn the power on at breaker/fuse box and test the

dishwasher operation by running a Rinse cycle.

(This should take about four minutes.)

3. Turn off the electrical power and check for leaks

ADJUSTING THE LEVELING LEGS

Now that all the connections are made and the machine

is in place under the cabinet, you should make the final

height adjustment.

1. Using a 1/2" (12 mm) wrench, adjust the locking

nuts until the machine is level. (The machine may

have an inclination of 2° maximum without affecting

its performance.)

FASTENING THE DISHWASHER TO THE CABINET

It's necessary to fasten the dishwasher to the cabinet

so it won't tilt when the door is opened or if something

heavy is placed on the door. Use only the stainless

steel screws provided with the machine.

1. Use option A for U.S. or European standard

installations. Use option B only for European

standard installations.

2. Cover the screw heads with the plastic plugs

provided with the machine.

3. When the machine is properly attached, check that

the feet are tight against the floor and that the

machine is level.

NOTE: When it is not possible to attach the dishwasher

to the cabinet, you should install tip guards.

(See "Tip Guards" on page 2.)

Page 8

THE W W W W W A A A A A TER SUPPL

THE

TER SUPPLY Y Y Y Y

TER SUPPL

(1) Hot water supply

(2) Shut-off valve

NOTE:

You should only install the number 4 tubing

before you push the machine into position.

Tubing number 5 is to be fitted when the

machine is in position.

under the dishwasher.

4. Make sure that no kinks have developed in the drain

lines.

If there are no leaks and the dishwasher seems to be

working properly, continue with the installation.

2. When the feet are properly

adjusted, tighten the locking

nuts to the base pan.

NOTE: When adjusting the unit lower than 33-1/4" the

toe kick has to be modified; the holes for the

access panel and fill strips need to be

elongated.

NOTE:

Option A can be used for U.S. or European

installations. Use option B for European

standard installations only.

(3) Alternate locations

(4) & (5) Tubing