Ambient Technologies RCB Instruções de instalação e de utilização
Procurar online ou descarregar pdf Instruções de instalação e de utilização para Controlo remoto Ambient Technologies RCB. Ambient Technologies RCB 2 páginas. Basic on/off remote control
Também para Ambient Technologies RCB: Instruções de instalação e de utilização (2 páginas), Instruções de instalação e de utilização (5 páginas)
RCB
Basic On/Off Remote Control
INSTALLATION AND OPERATING INSTRUCTIONS
This basic on/off remote control system provides a safe, reliable,
and user-friendly remote control for millivolt valve gas appliances.
The system can be manually turned on and off with the transmit-
ter. Always check with the home owner's manual of the appliance
for additional information, warnings regarding accessory installa-
tion before connecting this remote control system.
Carefully inspect the contents for shipping damage. If any parts
are missing or damaged, immediately contact the dealer from
whom you purchased the kit. Do not attempt to install any part of
the kit unless all parts are in good condition. Please keep this
manual for future reference.
CONTENTS OF KIT
Description
Transmitter
Battery Alkaline AAA ( for Transmitter)
Receiver (Assembly) consists of :
Receiver Box
Slide Button-Black (On/RS/Off)
Battery Alkaline AA (for Receiver)
Wall Cover Plate-Black
Wall Cover Plate-White
Slide Button-White (On/RS/Off)
Screws (for Wall Cover Plate)
Plug-In Wiring Assembly – 18" Inches
Installation Instructions
Velcro (Loop and Hook)
Screws (for fireplace system control covers)
FEATURES/SPECIFICATIONS
•
Battery Powered Transmitter and Receiver
•
Easy Access Front Battery Door
•
Pre-Programmed for Quick Installation
•
16 Security Codes
•
Quick Disconnect Wiring Assembly
WARNING
Important Safety Information
•
Read this manual thoroughly prior to installing, programming
or operating any remote control.
•
This remote control system is designed for use with a milli
volt gas valve system. Do not use this remote control system
on applications with voltages above 30 Volts AC.
•
This remote control system requires three (3) "AAA" and four
(4) "AA" alkaline batteries to power the transmitter and
receiver. Wiring must conform to appliance requirement and
building codes/ordinances as required by local and national
code authorities having jurisdiction.
•
Do not short (or jumper) across the gas valve terminals to test
the remote control installation. This could damage the unit
and void the warranty.
•
This remote control system should only be used as described
in this manual. Any other use is not recommended and will
void the warranty.
Turn appliance OFF and allow to cool before
installing or servicing. DO NOT connect
110-120 VAC wiring to the milli-volt gas control
valve. The remote operator must be installed
exactly as outlined in these instructions. Read all
instructions completely before attempting
installation. Follow instructions carefully during
installation. Any modification of components will
void the warranty and may cause a fire hazard.
INSTALLATIONS
Remote Receiver:
The remote receiver may be wall mounted or installed in the
appliance per the appliance homeowner's manual. Refer to the
Homeowner's Manual for special installation instructions. If
wall mounted, the remote receiver must be installed in a junction
box with cover plate provided. Failure to follow the installation
instructions found in the appropriate Homeowner's Manual will
void the warranty and may cause a fire hazard.
Installing Batteries:
The remote receiver uses four (4) "AA"- size batteries. To install
batteries,
1.Open the battery door by
pressing the two tabs located on
the door.
2.Install the batteries as indicated
Qty
in the receiver cover.
1
3.Close the battery door until the
3
door tab snaps in place.
1
4.To install the receiver into a
wall junction box, install the
receiver with the screws
4
provided .
1
5.Gently, install the slide switch
1
back to the receiver stem.
1
6.The batteries should be replaced
2
at least once every 6 months or
1
when the battery indicator
1
flashes.
1
2
Installing Wire:
This system comes with an 18 inch pre-assembled wire assembly.
Insert the white terminal to the back of the receiver. The terminal
wire block can only be installed one way. Do not force the termi-
nal plug onto the receiver.
Follow the homeowner's manual for connecting the two (2) 1/4"
female spade terminals to the millivolt valve.
For applications longer than 18 inches, use 18 gauge wire, 105ºC
rated, with no splices. Connect to the two (2) 1/4" female spade
wiring terminals. Wire can be no longer than 20 feet.
Make sure that the wires do not contact the
appliances any place other than at the terminals.
Exposure to temperatures higher than 105C
(250ºF) may cause the receiver to malfunction or
fire hazard.
Remote Transmitter:
Installing Batteries:
The remote transmitter uses three (3)
"AAA"- size batteries. To install
batteries,
1.Press down the battery door tab
and lift up and remove the battery
door.
2.Install the batteries as indicated on
the receiver cover.
3.Close the battery door by snap-
ping in place.
4. The batteries should be replaced
at least once every 6 months or
when the battery indicator flashes.
Setting Privacy (DIP) Switch on Receiver and Transmitter:
The remote receiver and transmitter privacy (DIP) switches are
preset at the factory. The receiver and transmitter privacy (DIP)
switches are preset at the factory. In the event of activation or
interference from other nearby transmissions, reset the code using
Battery Door
the following procedure:
1.Slide the code switches on the transmitter or receiver to your
choice of ON or OFF position. Switches #1, #3 and #4 are pre-
set to "ON", and #2 is preset to "OFF" for both the transmitter
and receiver.
2.The switches on the transmitter and receiver must match in
order for the system to work.
3.The system is now ready to operate.
Dip Switch (Default)
Battery
Door
Tab
Back of the Transmitter
Transmitter
Do not use two (2) or more remote control systems
in the same area with the same dip switch settings,
as they will communicate with each other. This
may cause the appliances to malfunction.
Receiver