Ambient Technologies RCST Instruções de instalação e de utilização - Página 2

Procurar online ou descarregar pdf Instruções de instalação e de utilização para Controlo remoto Ambient Technologies RCST. Ambient Technologies RCST 2 páginas. Standard thermostatic on/off remote control

Imprimir página

Ambient Technologies RCST Instruções de instalação e de utilização

OPERATIONS

Transmitter

General

The RCST Remote Control has two (2) operating

modes–Manual and Thermostatic. The control sys-

tem can be set to temperature ranges between 45°F

and 90°F.

The transmitter will operate the remote receiver

from 1foot to a maximum of 30 feet. The distance is

reduced when batteries are low or when the receiver

is inside a metal enclosure.

Initial Start-up

1. After initial power up or when RESET button is pressed, the

transmitter is reset. The reset button is located inside the battery

door.

2. During system reset, all features of the LCD display will be

visible. After one second, the LCD displays will be initialized. A

typical reset display is shown beside. Note that the temperature

scale is degree F.

3. Press On button to select between °C and °F display. It will exit

setting mode automatically after 10 sec-

onds if no key is pressed. The transmitter

will send an Off signal after reset.

4. After reset the transmitter is operating in

manual mode. The room temperature is

shown as above.

Manual Mode

1. Press the ON button once to turn on the appliance.

2. Press the OFF button to turn it off.

Thermostatic Mode

1. Press the AUTO button to enter the

thermostatic mode. "SET" temp icon will

appear on the lower LCD screen

2. In thermostatic mode, press the ON/▲

button or OFF/ ▼ button to set the de-

sired set temperature.

3. Once the setting is completed, the transmitter will automatically

turn on the ﬁ replace when the room temperature is below the set

temperature and turn off the appliance when the room tempera-

ture is above the set temperature within 1 degree.

4. There will be a slight delay in the response of the unit (on/off) to

a temperature. Room temperature is monitored every 3 minutes.

5. Press the Auto button to exit the thermostatic mode (Return to

Manual Mode). The "SET" temp icon will disappear on the lower

LCD display. The transmitter will be in the manual on/off mode.

Backlight

The backlight color will change according to the current temperature

range. If the room temperature is over 78°F(26°C), then the back-

light will be Red. If room temperature is less than 61°F(16°C), the

backlight will be Green. Backlight will be Blue if the room tempera-

ture is between 61-78°F (16-26°C). When any key is pressed the

backlight will turn on for 8 seconds and then turn off.

Low Battery Detection

1. When the battery voltage of remote is less

than 3.4V, the low battery icon will ﬂ ash.

The battery will be checked every minute.

If the battery voltage of remote is less

than 3.2V, the remote will send the ﬂ ame

off command to the receiver and turn off the ﬂ ame.

2. The transmitter will not operate with low batteries. Change the

battery before the battery is too weak for normal operation.

TURN THE UNIT OFF BEFORE REPLACING BATTERIES.

50D0095 RCST.indd 2

Child-Proof Protection

1. Press and hold ON and OFF buttons

simultaneously for 3 seconds to enter

child-proof mode.

2. The transmitter will not work until child-

proof mode is deactivated by pressing

the ON and OFF buttons simultaneously

for 3 seconds again to exit child-proof mode.

Transmitter Thermal Shutdown

1. If transmitter measures a room tempera-

ture exceeding 99 degrees Fahrenheit, the

LCD will display "HI" and the transmitter

will turn off the appliance.

2. Transmitter will not function until the room

temperature has dropped below 99 degree

Fahrenheit.

3. If transmitter measures a room temperature less than 40 de-

grees Fahrenheit, the LCD will display "LO" and NO SIGNAL will

be sent to turn on the appliance.

Receiver

Slide Switch

1. ON position: the system will remain on until the slide switch is

placed in the OFF or RS position.

2. RS position: the system will only operate if the remote receiver

receives a signal from the transmitter.

3. OFF position, the system is off. The slide switch should be

placed in the OFF position if you will be away for an extended

period of time. If the remote receiver is mounted out of children's

reach, the OFF position also functions as a safety device by both

turning the system off and rendering the receiver inoperable.

TESTING YOUR NEW

REMOTE CONTROL SYSTEM

1. Light your gas appliance following the appliance lighting instruc-

tions that come with the appliance. Conﬁ rm that the pilot light is

on; it must be in operation for the remote control to operate the

main gas valve. Appliance pilot control knob must be in the ON

position. Appliance ON/OFF switch must be in OFF position.

2. Slide the 3 position button on the remote receiver to the ON posi-

tion. The main gas ﬂ ame should ignite.

3. Slide the button to OFF. The ﬂ ame should extinguish (the pilot

light will remain on).

4. Slide the button to RS (the center position), then press the

transmitter to turn the system to ON. The main gas ﬂ ame should

ignite.

5. Press the transmitter to turn the system to OFF. The ﬂ ame

should extinguish (the pilot light will remain on).

TROUBLESHOOTING

Symptom

Causes

Action

LED light on receiv-

Low battery

Replace batteries.

er blinking or battery

icon displaying on

transmitter.

Display is blank.

Low battery

Check battery instal-

lation and replace

batteries.

Display looks "fun-

Low battery

Press "Reset" button

ny."

at the back of the

transmitter.

WARNING: Changes or modiﬁ cations to this unit not ex-

pressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Symptom

Causes

Action

Appliance does not

1. Wiring/electrical

1. Slide the switch

come on.

connections faulty

to ON. If appliance

comes on, wiring

is not the cause. If

appliance does not

come on, check wir-

ing connections.

2. DIP (Privacy)

2. Make sure the

switch setting on

transmitter and

transmitter does not

receiver have the

match receiver.

same DIP switch

settings.

3. Transmitter mea-

3. Move trans-

sures temperature

mitter to a cooler

exceeding 99°F and

place and wait until

shows "HI" on LCD

temperature drops

display.

below 99°F.

4. Distance between

4. Make sure the

the transmitter and

operating distance is

receiver is more

less than 20 feet.

than 20 feet.

Receiver cannot

Receiver is installed

Make sure the re-

detect signal.

in an enclosure.

ceiver is not inside a

tight enclosure.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

•

Re-orient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician.

WARRANTY

This warranty gives you speciﬁ c legal rights and you may also have

other rights that vary from state/province to state/province. Answers

to any questions regarding our limited warranty may be obtained by

writing our corporate ofﬁ ces.

Ambient Technologies warrants each new remote control against

any defects that are due to faulty material or workmanship to the

original owner, for a period of ﬁ ve years after the original date of pur-

chase. This warranty and our liability does not apply to batteries, nor

does it include damage to merchandise or the remote control result-

ing from accident, alteration, neglect, misuse, improper installation

or any other failure to follow installation and operating instructions.

Ambient Technologies agrees to repair or replace at its option any

Ambient Technologies remote control under warranty, provided it is

returned postage prepaid to our warranty facility in a padded carton

within the warranty period, with proof of the original date of purchase

and a brief description of the malfunction. This limited warranty does

not include the cost of removal or re-installation. All returns must

have a return authorization number from Ambient Technical Support.

149 Cleveland Drive • Paris, KY 40361

Technical Support: 800.398.6195

50D0095., Rev 3, 12/14

12/30/2014 9:07:18 AM