Aktakom ACM-2352 Руководство пользователя - Страница 2
Просмотреть онлайн или скачать pdf Руководство пользователя для Измерительные приборы Aktakom ACM-2352. Aktakom ACM-2352 8 страниц. Clamp & watt meter
Печатать страницу
Introduction
Congratulations on your purchase of True RMS Clamp Meter. This meter measures AC Current, DC Current, AC/DC Voltage, Resistance,
Capacitance, Frequency, Diode Test, Duty Cycle and Continuity. The molded case is designed for heavy duty use. This meter is shipped
fully tested and calibrated and, with proper use, will provide years of reliable service.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for further
information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages may be present
Double insulation
This WARNING symbol indicates a potentially hazardous situation, which if not avoided, could result in death or
WARNING
serious injury.
This CAUTION symbol indicates a potentially hazardous situation, which if not avoided, may result damage to the
CAUTION
product.
PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY
OVERVOLTAGE CATEGORY I
Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in which measures are taken to limit the transient
overvoltages to an appropriate low level.
Note – Examples include protected electronic circuits.
OVERVOLTAGE CATEGORY II
Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be supplied from the fixed installation.
Note – Examples include household, office, and laboratory appliances.
OVERVOLTAGE CATEGORY III
Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.
Note – Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed
installation.
OVERVOLTAGE CATEGORY IV
Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation.
Note – Examples include electricity meters and primary over-current protection equipment
SAFETY NOTES
•
Do not exceed the maximum allowable input range of any function.
•
Do not apply voltage to meter when resistance function is selected.
•
Set the function switch OFF when the meter is not in use.
•
Remove the battery if meter is to be stored for longer than 60 days.
WARNINGS
•
Set function switch to the appropriate position before measuring.
•
When measuring volts do not switch to current/resistance modes.
•
Do not measure current on a circuit whose voltage exceeds 600V.
•
When changing ranges, always disconnect the test leads from the circuit under test.
CAUTIONS
•
Improper use of this meter can cause damage, shock, injury or death. Read and understand this user manual before operating the
meter.
•
Always remove the test leads before replacing the battery or fuses.
•
Inspect the condition of the test leads and the meter itself for any damage before operating the meter. Repair or replace any
damage before use.
•
Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC. These voltages are considered
a shock hazard.
•
Always discharge capacitors and remove power from the device under test before performing Diode, Resistance or Continuity
tests.
•
Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed
electrical contacts. Other means should be used to ensure that the terminals are not "live".
•
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
•
This device is not a toy and must not reach children's hands. It contains hazardous objects as well as small parts that the children
could swallow. In case a child swallows any of them, please contact a physician immediately
•
Do not leave batteries and packing material lying around unattended; they can be dangerous for children if they use them as toys
•
In case the device is going to be unused for an extended period of time, remove the batteries to prevent them from draining
www.tmatlantic.com
2