barkman BELVEDERE Руководство по эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Крытый камин barkman BELVEDERE. barkman BELVEDERE 2 страницы. Rosetta landscape kits circle firepit
Печатать страницуIMPORTANT: READ PRIOR TO INSTALLATION
It is the responsibility of the consumer to read and follow the proceeding information.
1. The consumer is responsible for reviewing the local regulations pertaining to the installation and use of this product. Please confirm that
use of this product is in compliance with the by-laws, regulations, building codes and laws of your jurisdiction before using.
2. Make sure that you locate your respective gas lines, wires, water pipes, and/or any above ground and underground services in your area
and install your firepit in the proper distance away from them. Check with your provider for location and distance requirements prior to
installation.
3. Check with your insurance provider concerning the installation, use, value implications and/or any other considerations in regards
to your Belvedere Circle Firepit Kit. Firepits should not be placed directly on concrete products as high heat can adversely affect the
integrity of the product.
4. Firepit is not suitable for large fires. Fire size should not allow flame to contact the top layer. Firepits should not be placed directly on
concrete products as high heat can adversely affect the integrity of the product.
IMPORTANT: Be careful not to touch the steel liner while it's hot. It can still retain heat long after the fire has been extinguished.
Base Preparation
If installing firepit on an unstructured base, please ensure to
follow these steps:
1. Mark out the location for your firepit. Area should be slightly
larger than 58" in diameter as dimensions of kit are nominal.
2. Excavate for drain stone base (approximately 6").
3. Fill excavated area with drain stone, level and compact. The
finished height of the firepit will be approx. 14.25" above base.
Instructions
Steps
1. Place and center steel firepit liner on prepared base.
2. Place 3"& 6" high blocks per the block layout pattern shown
above. Keep the back of the blocks approx. 2" off of the steel ring.
3. After placing blocks around the ring, adjust the blocks to close the
circle and fit it tightly. If the blocks do not close the circle, move
all the blocks slightly in. If the blocks seem too long, move the
blocks slightly out.
4. Fill gaps between ring and blocks with pea gravel. This will hold
the ring in the center of the firepit.
5. Place the cap layer in a circle around the firepit. Adjust the caps in
or out to make them fit tightly together. Caps should slightly over-
hang the front of the blocks and be slightly forward of the outside
edge of the steel ring.
Note: This manual was updated in June
2018. Check www.barkmanconcrete.
com/resources for any manual updates.
Steinbach Office
Winnipeg Office
152 Brandt Street
909 Gateway Road
Steinbach, MB R5G 0R2
Winnipeg, MB R2K 3L1
06-2018
T (800)-461-2278
T (800)-342-2879
F (204)-326-5915
F (204)-663-4854
14.5"
F
F
F
F
D
B
C
B
F
B
F
B
A
B
D
A 17" x 6"
B
11.5" x 6"
Vancouver Office
Calgary Office
2104-290 Newport Drive
813 McCool St. Box 1136
Port Moody, BC V3H 5N2
Crossfield, AB T0M 0S0
T (778)-689-7670
T (403)-946-4630
F (604)-949-0321
F (403)-946-4631
Caps don't contact
steal ring
Drainstone
58" Diameter
Blocks
F
F
F
F
D
E
E
A
B
B
B
A
F
F
C
D
E
E
E
C 6" x 6"
D 17" x 3"
E 11.5" x 3" F 6" x 3"
38" dia steel ring
2" gap
Cap Layer
Steel Ring
F
F
F
F
E
E
C
B
A
B
C
D
A
C
E
E
E
F cap
2