American Standard Champion 4 MAX Right Height 231BA Series Руководство по установке - Страница 6
Просмотреть онлайн или скачать pdf Руководство по установке для Туалеты American Standard Champion 4 MAX Right Height 231BA Series. American Standard Champion 4 MAX Right Height 231BA Series 8 страниц. 2-piece toilet
Печатать страницу
6
BOLT CAP
WASHER
NUT
CLOSET BOLT
7
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8a
Before continuing, determine the type of water supply connection you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as illustrated
to insure water-tight connection. Use of
existing coupling nut may result in water
leakage. Water supply tube or pipe
must extend at least 1/2" inside
threaded shank of valve (does not apply
to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
WARNING: Do not use plumber's putty, pipe dope, or any other sealant on the
!
water supply connection to this tank. If the connection leaks after hand tightening,
replace the supply line. If the connection continues to leak with the new supply line,
replace the fill valve. Warranty is void if any type of sealant is used on the water
supply connection.
9
TOP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
FLOAT
CUP
FILL
VALVE
VALVE
BODY
ADJUSTABLE
HEIGHT
LOCK NUT
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
BOLTS
CLOSET FLANGE
METAL FLANGED
METAL SPIRAL
TUBING
TUBING
LOCK NUT
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing
Use existing spiral cone
coupling nut
washer. Fluidmaster cone
and washer.
washer may not seal
completely on spiral type
supply line.
CAUTION: Overtightening of
LOCK NUT or COUPLING
NUT could result in breakage
and potential flooding.
ARM
NIPPLE
REFILL
TUBE
TANK
LEVER
Fig. 9a
WATER LEVEL
ADJUSTMENT
ROD
SHANK
WASHER
THREADED
SHANK
PARTS FOR WATER
CONNECTION
(SEE STEP 8)
Diagram 1
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
b. Install caps on washers. (If necessary, cut bolt height to
size before installing caps.)
c. Smooth off the bead of sealant around base. Remove
excess sealant.
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
EXISTING
COUPLING
CONE
NUT
WASHER
COUPLING
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Captive cone
washers already
included. No
additional
washers needed.
ADJUSTMENTS:
Turn supply on.
a.
Adjust water level to level
indicated on tank by adjusting
float cup. See Step 10.
b.
If bowl fails to siphon, an
adjustment may be required with
the lift chain. Simply remove the
bead chain from the retainment
clip (see Fig. 9a) and take up
slack on the chain, and reinsert
on lift rod. Make sure the chain
is not too taut.
- 2 -
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
8b
With correct washers in place (see Step 8a),
tighten COUPLING NUT 1/4 turn beyond
hand tight.
DO NOT OVERTIGHTEN.
10
Turn on water supply.
Submerge the FLOAT
CUP under the water for
30 seconds. Adjust the
water to desired level by
turning WATER LEVEL
ADJUSTMENT ROD
and moving FLOAT
CUP up or down.
7 3 0 8 6 5 - 10 0 Rev. M