American Time SiteSync IQ Краткое руководство по эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Оборудование для звукозаписи American Time SiteSync IQ. American Time SiteSync IQ 2 страницы. Wireless system controller with standard gps & magnetic mount tx antenna
Также для American Time SiteSync IQ: Краткое руководство по установке (2 страниц), Руководство по установке и эксплуатации (2 страниц), Руководство по установке и эксплуатации (13 страниц), Руководство по установке и эксплуатации (7 страниц), Руководство по установке и эксплуатации (6 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по установке (2 страниц), Краткое руководство по эксплуатации (2 страниц), Краткое руководство по эксплуатации (2 страниц)

American Time SiteSync IQ Краткое руководство по эксплуатации
QUICK START INSTALLATION GUIDE
1
Unpack the box
Remove the components and system controller from the box. Save the
packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Premium GPS receiver with 50' cable and mounting kit
(B)
• Power supply
• Magnetic mount TX antenna with 12' cable
• USB Flash drive
• Installation and Operation Manual
3
Choose your location
a.
Choose a location for the GPS receiver outside with a clear view
of the sky. The included mounting bracket allows for mounting on
the side of a building or other structure. The included set of u-bolts
can be used to attach the bracket and GPS receiver to a mast.
Note:
Avoid high voltage equipment and excessive roof overhang when
choosing location.
b.
Locate the system controller in an area with a network drop, or run
an Ethernet data cable to the unit from a network switch or hub.
c.
Choose a location for your magnetic mount TX antenna either
outside or inside at the highest central location in your facility.
Note:
The TX antenna must be
located at least 4' away from
the system controller and must
4 ft
minimum
always point up or down, never
horizontal. The cable length
cannot be extended.
System controller located
high & central with Ethernet
drop for time reference
TX Ant signal
GPS signal in
out to clocks
INST-SSIQ-N-P
Rev 14 December 18, 2023
4
Connect cables to the system controller
a.
Connect the GPS antenna to the PREM GPS port
Connect a CAT 5 or higher Ethernet patch cable (not included) to the
ETHERNET RJ45 port.
b.
Connect the System Controller power supply to the POWER INPUT port
c.
Connect magnetic mount TX antenna to TX ANT port
d.
Plug 110v cord into power source. Turn the POWER SWITCH
on the back of the system controller to the on position.
(A)
See the SiteSync IQ Installation & Operation Manual for detailed instructions.
(C)
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
GPS=Y
5
Use the Setup Wizard
a.
PRESS 1 to start the Setup Wizard (Page 10 in Installation Manual).
b.
Create a 4 digit User Lock or enter 0000 to disable this feature. PRESS O.
c.
Create a 4 digit Service Lock (for advanced features) or
enter 0000 to disable this feature. PRESS O.
d.
Select local time zone by using the <> keys. PRESS O.
USET=Eastern, USCT=Central
USMT=Mountain, USPT=Pacific
Note:
(Appendix B in Installation Manual).
PRESS 8 to select
e.
automatic DST (Daylight Saving Time) or 0 to disable DST
if your location doesn't observe DST. PRESS O.
PRESS 1 for 12-hour mode - AM/PM (1:00PM).
f.
PRESS 2 for 24-hour mode - Military (13:00).
(A)
.
(C)
.
A
C
B
To local power (110vac)
Set Menu LOCAL
Time Zone Code:
99=Custom
There are 40 options to choose from
<>=Scroll
Note: Screen will
advance immediately
SITESYNC IQ
WIRELESS CLOCK SYSTEM
®
5
g.
PRESS 1 to Setup Sync Options
h.
PRESS 1 for (GPS) or PRESS 2 for Ethernet priority
PRESS 1 to Enable DHCP or Press 2 to Disable DHCP. PRESS O.
i.
j.
Use the keypad to enter the Unit IP Address. PRESS O.
(B)
.
k.
Enter the Subnet Mask. PRESS O.
Enter the Gateway IP. PRESS O.
l.
m. Enter the DNS IP. PRESS O.
n.
PRESS 1 to use a Manual IP, or PRESS 2 for
a DNS IP Time Server. PRESS O.
• If 1 Manual IP, enter Time Server Address and
PRESS O to accept. Repeat for Alternative Time Server.
• If 2 DNS IP, PRESS O.
Note:
this value can only be changed in Remote Connect.
o.
Press O to accept the default (80) Port Number
p.
To confirm proper set up, press O to sync.
• If successful, "Ethernet Sync Successful" will display.
• If not successful, "Ethernet Sync Failed" will display. Refer to the
troubleshooting guide in manual.
q.
PRESS 8 to sync GPS. If Successful, PRESS O to Set and exit.
• If not successful, "Sync Failed" will display. Refer to the troubleshooting
guide in the manual.
r.
"Setup Wizard Successfully Completed" will display.
6
Select Clock Code (for existing wired clock systems)
Continue on to Step 7 if you are not connecting wired clock circuits.
a.
Reference Appendix I in the manual for clock codes and wiring information
if you have wired circuits. Clock Code 01 is set from the factory. If 01 is the
code required, skip to 7 – Verify Unit is Transmitting. If the code needs to be
changed continue to next step.
b.
PRESS P6 and enter your service lock to access the Configuration
Menu. From the Config Menu, PRESS 3. This feature is used to set the
clock code for wired clock circuits. Enter the clock code using the keypad,
or choose 00 if you want to disable the clock code feature. Press O.
7
05
USCT
Verify Unit is Transmitting
OK=Accept
The system controller now shows the correct time and date. You will no
longer be prompted on power-up for setup information.
TX should display for about three seconds
every 30 seconds (approximately the top
and bottom of every minute) in the bottom
right corner of the screen.
Skip if
1
is selected
in step i.
MON
MAR
15
2021
10:38:06 AM
USCT
American Time
Status=AUTO
TX