QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Premium GPS receiver with 50' cable and mounting kit
• Power supply
(B)
• Campus TX antenna kit
(C)
• 9 pin data cable
(D)
• External Transmitter and power cord
• Installation and Operation Manual
3
Choose your location
• Choose a location for the GPS receiver outside with a clear
view of the sky. The included mounting bracket allows for
mounting on the side of a building or other structure. The
included set of u-bolts can be used to attach the bracket and
GPS receiver to a mast.
Avoid high voltage equipment and excessive roof overhang
when choosing a location.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
System controller
located high and central
TX Ant signal
out to clocks
GPS signal in
4
Connect cables to the system controller
A.
Connect the GPS antenna to the PREM GPS port.
• If desired for a redundant connection to the time server,
connect a CAT5 or higher Ethernet cable to the Ethernet port.
Refer to the SiteSync IQ Installation & Operation Manual for
detailed instructions on using multiple time sync methods.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect campus antenna to ANTENNA port on the External
Transmitter. *Lightning arrestor must be grounded per local
(A)
electrical code.
D.
Connect the 9 pin data cable to the DATA port on the External
Transmitter.
Connect the 9 pin data cable to the EXT TX port on the
(E)
system controller
E.
Connect the External Transmitter power cord to the POWER
INPUT port on that unit
Plug 120v cords for both units into power source. Turn the POWER
SWITCH on the back of the system controller and external
transmitter to the on position.
External
Transmitter
SITESYNC IQ
*
See above
To ground
System Controller
A
D
B
D
E
C
To local
power
(120vac)
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
(Page 9 in Installation Manual)
2. Create a 4 digit User Lock or enter 0000 to disable this
feature. Press
.
Tip: Record this password.
O
3. Create a 4 digit Service Lock (for advanced features) or enter
0000 to disable this feature. Press
O
Tip: Record this password.
4. Select local time zone by using the
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from.
5. Press
to select automatic DST (Daylight Saving Time) or
8
to disable DST if your location doesn't observe DST.
0
Press
O
6. Press
for 12-hour mode - AM/PM (1:00PM).
1
Press
for 24-hour mode - Military (13:00).
2
7. To confirm proper set up, press
to sync.
8
• If successful, "GPS Sync Successful" will display
• If not successful, "GPS Sync Failed" will display. Re-try
by pressing
again.
8
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
MON MAR 14 2016
10:38:06 AM USCT
American Timel
Status=AUTO
GPS=Y
.
keys. Press
.
<>
O
Note: Screen
will advance
immediately
TX
Печатать страницу