DoorHan SWING-3000 Руководство по установке и эксплуатации - Страница 11

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Открыватель ворот DoorHan SWING-3000. DoorHan SWING-3000 16 страниц.

7. operator proGrammInG

To go into the BASIc prOGrAmmInG mOde, press the key "f". On the left display you will see the name of the function, which

is to be programmed and on the right display you will see current value of this function. The value can be changed by pressing

keys "+" or "–". If you press the key "f" again, you will see the name of the next function on the display and you will be able to

program it and so on. After you have programmed all the functions you can exit the programming mode by pressing the key "f".

display

programming of pause time before automatic closing: 1 — 10 s, 2 — 20 s, 3 — 30 s, 4 — 60 s,

first leaf closing delay: 1 — 1 s, 2 — 5 s, 3 — 10 s, 4 — 15 s, 5 — 20 s, 6 — 25 s, 7 — 30 s, 8 — 35 s, 9 — 40 s

To go into AdVAnced prOGrAmmInG mode, press the key "f" and holding it down, press the key "+". you will see the name of

the function to be programmed. On the right display you will see the current value of the function, which can be changed by pressing

the keys "+" or "-". If you press the key "f" repeatedly, you will see the name of the next function on the display and you will be able

to program it. After all the functions have been programmed, you can exit the programming mode by pressing the key "f".

display

Indicator light: 1 — 10 s, 2 — 20 s, 3 — 30 s,4 — 60 s, 5 — 90 s, 6 — 120 s, 7 — 180 s, 8 — 360 s, 9 — 420 s

If the function is on and the pause time is preset than the gate closes as soon as the safety devices

If the function is on the gate closes/opens only if a corresponding button is hold down У — on; n — off

If the function is on the opening gate can be stopped only by the limit switches, the closing gate

In order to program the motor operation time, close the gate and couple the operators (if there is a rabbet, program a leaf

opening/closing delay). Then enter the basic programming mode, select function "f", press and release "+." The leaves will begin

to open. After they reach the limit switches, the leaves will stop. At this moment give a control command. programming is done.

press "f" again to leave the basic programming mode. When the next control command is given the leaves will start moving in

accordance with the programmed operation mode.

5 — 90 s, 6 — 120 s, 7 — 180 s, 8 — 360 s, 9 — 420 s

programming of the first motor force: b1 — minimal; b9 — maximal

programming of the second motor force: С1 — minimal; С9 — maximal

Second leaf opening delay: 1 — 1 s, 2 — 2 s, 3 — 3 s, 4 — 4 s, 5 — 5 s

programming of the motor operation time

counter of the cycles (one division — 100 cycles)

maximal force at the starting time: У — on; n — off

pre-activation of a signal lamp (5 s): У — on; n — off

Safety devices: У — immediate reverse; n — reverse after the opening is cleared

are actuated У — on; n — off

can be stopped in a usual way У — on; n — off

function

operator proGrammInG

on default