AmerTac Westek LPL905M Руководство пользователя

Просмотреть онлайн или скачать pdf Руководство пользователя для Светильник AmerTac Westek LPL905M. AmerTac Westek LPL905M 2 страницы. Motion activated led safety light

Печатать страницу

LPL905M Owner's Manual

Location of Controls

1. 4 LEDs

2. ON/OFF/DIMMER Switch

3. Battery Compartment*

4. Motion Sensor

5. Slide Mount Bracket

6. Motion Sensor Activation Switch

*Underneath unit

Installation

Hook and Loop Tape (included)

NOTE: Hook and loop tape may be cut to desired size for easier removal.

1. Check the location of where you want to place the light. Make sure it is clean and there is no debris or dust.

2. Place the two pieces of hook and loop tape together so the hook and loop sides adhere to each other.

3. Remove the plastic covering on one sticky side of the tape.

4. Place the hook and loop tape on the back side of the Slide Mount Bracket.

5. Remove the plastic covering on the other sticky side of the tape.

6. Place the light in the desired location. Press ﬁ rmly for ﬁ ve (5) seconds so the tape adheres to the surface.

CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage surface.

Screws (included)

1. Remove printed paper mounting template from back of unit. Remove the light from the Slide Mount Bracket.

2. Using the paper template, mark and drill two (2) pilot holes in the location where you want to mount the light.

3. Place screws (included) through the mounting bracket and in pre-drilled holes. Tighten the screws to secure the mounting bracket. Do not overtighten.

4. Slide the light back into the Slide Mount Bracket.

5. To remove the light from the Slide Mount Bracket, simply slide pull the light up.

Operating Directions

Light Positioning

• The LED Accent Light's light head can extend up to 60°.

• Pivot the lens as needed to light desired area.

NOTE: Make sure not to over-extend the light head.

Damaging the unit will VOID the warranty.

ON/OFF/DIMMER Operation

• Press power symbol once for full brightness.

• Press again for softer light.

• Press a third time to turn the light OFF.

Motion Sensor

The light features an optional Motion Sensor which when activated will turn the light ON automatically when motion is detected. The light will also shut OFF automatically, after a

period of time when no motion is detected. It detects motion within 6.6 feet (2m) of the motion sensor. To use this feature, simply slide the motion sensor activation switch to the

desired location.

NORMAL - Motion sensor is inactive. (Use main ON/OFF Switch to activate the light.)

AUTO-30S - LEDs will turn OFF after 30 seconds if no motion is detected.

AUTO-60S - LEDs will turn OFF after 60 seconds if no motion is detected.

Perfect for use inside cabinets and closets.

Motion sensor is designed to detect motion within 6.6 feet (2m) of sensor. For best operation wave hand at a medium speed in front of motion sensor to activate light.

Inserting/Replacing the Batteries

If the LEDs appear to be dim this is an indication that your batteries need to be replaced.

1. Remove battery compartment from accent light.

2. Remove old batteries (if replacing batteries).

3. Replace with three (3) new AAA batteries.

4. Make sure to follow battery polarity guide when installing

new batteries.

5. Replace battery compartment housing.

Battery Precautions:

1. Use only the size and type of batteries speciﬁ ed.

2. Always purchase the correct size and grade of battery most suitable for the intended use.

3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device.

4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.

5. Replace all batteries of a set at the same time. Do not mix old and new batteries.

6. Clean the battery contacts and also those of the device prior to battery installation.

7. Do not dispose of batteries in ﬁ re.

8. Remove batteries if consumed or if product is to be left unused for an extended period of time.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Modiﬁ cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.

Limited Warranty

Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited

express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The

Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions

explained fully in the Limited Warranty on the website.

MOTION ACTIVATED

LED SAFETY LIGHT

0-60°

250 Boulder Dr.

Breinigsville, PA 18031

610-336-1330

www.amertac.com

Made in China / Fabriqué en

Chine / Fabricado en China

I18-0075-A