Dorma TS 99 FLR-K Инструкции по креплению - Страница 3

Просмотреть онлайн или скачать pdf Инструкции по креплению для Дымовая сигнализация Dorma TS 99 FLR-K. Dorma TS 99 FLR-K 4 страницы.

Печатать страницу

DORMA

FIXING INSTRUCTIONS

Technical Data TS 99 FLR-K

Input:

Output:

Type of Protection:

Protection class:

Smoke switch:

Temperature:

Technical Data, Hold-open Device (EMF)

Operating voltage:

Power input:

Duty factor:

• Work on electrical equipment and systems may

only be performed by properly trained specialist

personnel.

• Check to ensure that the line power supply (230V

AC) has been disconnected and is no longer live.

• IA 10 A/B miniature circuit breaker must be

provided in the supply circuit. This can also be

used as the isolator for disconnecting the FLR-K

and making it dead.

• The power cable leading to the FLR-K must be

properly secured to ensure effective strain relief.

• The power cable (NYM) conductor cross section

should be not greater than max. 1.5 mm

conductor is not electrically utilised. The terminal

(PE) should, however, be used where a PE

conductor is provided.

• Fire/smoke detectors controlling hold-open

systems must not be used to actuate any further

alarm devices (e.g. fire alarm transmission

☞

systems).

• If the optional alarm module is installed, the cable

connecting it to the smoke switch must be led over

and across the measurement chamber in order to

ensure that smoke penetration is in no way

hindered.

• According to the guidelines for hold-open systems

issued by the Institute of Building Technology,

Berlin, it must be possible to release every hold-

open device by manual means. If free-swing door

closers are used, release must be initiated by a

manual pushbutton. The manual release

pushbutton used for this must be red and carry the

inscription "Close Door". The pushbutton must be

in the immediate vicinity of the door (barrier) and

must not be concealed when the door (barrier) is

open.

Integral lintel-mounted smoke detector.

Electro-magnetic hold-open device.

Ceiling-mounted smoke detector.

DORMA HT manual release pushbutton for hold-

open devices.

1 )

Guidelines for hold-open systems issued by the Institute for Building Technology,

Berlin. In countries outside Germany, consult local regulations.

TS 99 FLR-K EN 2-5

230 V AC +10%/-15%

120 mA/28 VA / 50 Hz

24 V DC /460 mA / 11 W

IP 30

24 V DC/50 mA

-20°C/+60°C

24 V DC

2 W

100 % continuous duty

The PE

Installation arrangement of the FLR-K for

applications where the bottom surface of the ceiling

is less than 1m above the bottom edge of the lintel

on one or both sides of the door.

See separate sheet for associated connection

diagrams.

If the bottom surface of the ceiling is more than 1m

above the bottom edge of the lintel on one or both

sides of the door, two ceiling-mounted smoke

detectors must be installed in addition to the lintel-

mounted detector (FLR-K)

See separate sheet for associated connection

diagrams.

Drill fixing points for closer and slide channel using

TS 99 FLR-K template or as per dimensioned

drawing.

Drill holes of 12 mm dia. for the 230V AC power

cable (by others) and of 10 mm for connection to the

TS 99 FL, manual pushbutton and any required

ceiling-mounted detectors. Install cabling.

Fix junction box.

Fix mounting backplate.

Fix closer to the mounting backplate.

Ensure that the cable is located in the mounting

backplate groove and that it remains undamaged.

Connect 24V DC supply cable to the junction box

terminal

Connect interconnecting cable

Connect the internal cable to the connector of the

electro-hydraulic hold-open device

Fit arm at an angle of approx. 10° from the door leaf

and tighten fixing screw

LH (ISO 6) handing:

Fix FLR-K unit.

RH (ISO 5) handing:

Rotate slide channel 180°

Fix FLR-K unit.

Close valve for adjusting closing speed

door approx. 45°

Push arm towards slide channel

slide block

Adjust spring strength (closing force).

Adjust closing speed 180° - 0°

Adjust latching action 7° - 0°

Fit end caps

Break out spindle recess tab

Ensure that the cables are not damaged in this

process.

Clip on DORMA logo badge

☞

1) 1) 1) 1) 1)

☞

1) 1) 1) 1) 1)

, and open

and connect to

and fit clip-on cover