Dot-Spot Clarios Eco 230 V Руководство по эксплуатации - Страница 9

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Ландшафтное освещение Dot-Spot Clarios Eco 230 V. Dot-Spot Clarios Eco 230 V 13 страниц. Garden spot

Печатать страницу

Configurations

Electrical connection

Order number

5 m H05 RN-F rubber cable,

.52

with IP 44 Schuko plug

Optionales Sonderzubehör

ground spike ES 20

93000

marten repellent MS

93001

installation extension MV

93201

dazzle protection BS eco

93104

Safety

Intended use

The garden and object spot clarios eco 230 V is designed for providing effect lighting for plants

and objects as well as for permanent installation. It is designed for operating in moderate climatic

zones. The spot is meant for operating with for operation with mains voltage 230 - 240 V, 50 - 60

Hz. In case of detailed lighting planning, please request the light distribution curves (LDC).

Installation to be carried by an expert

The installation may only be carried out by appropriately trained professionals.

In case of damage to the spot or the connection cable, it must not be operated any further and

must be disconnected immediately from the mains. In case of contact with 230 - 240 V mains

voltage it can lead to serious injuries or even death!

Safety instructions

During installation, the relative safety regulations have to be followed. The spot is operated

with mains voltage 230 - 240 V. To avoid danger and failures, prior or any work at the spot

or installation, disconnect the spot from the mains. The spot can't be opened. Connect the

spot only to sockets with a voltage of 230 - 240 V AC, 50 - 60 Hz. A wrong voltage may destroy the spot.

In order to protect the exposed connection cable from rodents it should be protected against mar-

tens (see installation accessories).

High ambient temperatures shorten the life of the LED's. Ensure a good heat dissipation in order to

guarantee a long life of the LED. During operation, do not expose the spot to ambient temperatures

of > 45°C. Do not cover the spot, provide free air circulation.

Do not open the housing of the luminary. The tightness of the clarios eco 230 V is only guaranteed

if also the outer sheath of the connection cable is undamaged and if the connection cable is bond-

ed in a waterproof way. Otherwise, because of the capillary effect, the penetrating moisture can

reach and destroy the electronics of the spot.

Comment

Termination possible by cutting the

Schuko plug

length 50 cm

length 10 cm, for raised assembly

stainless steel, put on from outside

Assembly

Preparation

Depending on the configuration, unpack all the parts included in the scope of delivery and check

them for completeness and intactness.

Dispose of the packaging material no longer needed in accordance with applicable regulations.

If you notice any damage from transport, immediately contact the dealer where you purchased the

luminary.

Mechanical installation

Mark the hole for substrate mounting through a hole in base of the mounting bracket. The dowel in-

cluded in the scope of delivery is suitable for installation in concrete, stone and masonry. Drill a hole

of Ø 8 mm and deeper than 50 mm into the substrate and insert the dowel into the hole. In case

of wooden substrates the mounting bracket can directly fixed using the supplied screw, without the

dowel. In case of hardwood the holes may require pre-drilling with Ø 3 mm.

Position the mounting bracket over the dowel, orientate it into the desired direction and screw it

down with the supplied screw.

Now, the clarios eco 230 V can be attached to the mounting bracket.

1. Thread a snap ring onto a screw, insert it through a hole at the upper end of the mounting

bracket, thread a plastic washer onto the screw and screw it laterally into the threaded holes on

the luminary housing. In order to do so, insert the spot in the mounting bracket.

2. Repeat that with the second screw, snap ring and plastic washer on the other side.

3. Pay attention to correct sorting: screw head, snap ring, mounting bracket, plastic washer, lumi-

nary housing.

4. Orientate the spot in the desired direction and screw it tight with a 4 mm hex key.

Installation using the ground spike

Drive the ground spike into the ground using a suitable tool. When using a metal hammer, please

put a piece of wood or the like between the hammer and the ground spike in order to protect the

latter. Then, screw the mounting bracket with the luminary onto the ground spike using the screw

and the snap ring provided with the ground spike. The snap ring is placed between screw head and

mounting bracket. Orientate the mounting bracket before screwing it down.

Installation using the mounting extension

The mounting extensions are designed for the use with the ground spike.

Screw the mounting extension onto the ground spike using the threaded pin. Screw tight the mount-

ing extension: in order to do so, use a pair of pliers and put a cloth or the like around the mounting

extension.

Then, screw the mounting bracket with the luminary onto the mounting extension using the screw

and the snap ring provided with the ground spike. The snap ring is placed between screw head and

mounting bracket. Orientate the mounting bracket before screwing it down.