Dot-x DNR V SERIES Руководство пользователя - Страница 8

Просмотреть онлайн или скачать pdf Руководство пользователя для Монитор Dot-x DNR V SERIES. Dot-x DNR V SERIES 12 страниц. 25 inch display
Также для Dot-x DNR V SERIES: Руководство пользователя (10 страниц)

Печатать страницу

INTRODUCTION

Congratulations on your purchase of a new DNR V Series 25 inch Display.

This manual has been prepared to act as a guide in the operation of your

monitor. Please read the following operating instructions carefully before

using your monitor so that you are familiar with all of its features and

capabilities. All precautions and safety warnings should be read and strictly

observed.

UNPACKING THE MONITOR

To unpack your monitor:

1. Untape and open the top flaps of the packing carton. The monitor will

be cushioned by foam inserts. The back of the monitor will be facing up.

2. With the top open, carefully roll the monitor carton so the top of the box

is positioned down. Remove the monitor by lifting the box up and off the

monitor and the inserts. Caution: A firm hold on the monitor must be

constantly maintained while it is being removed from its packing carton.

3. Inspect the monitor thoroughly for any damage that might have occurred

during shipping.

If any damage to the monitor is found, report it immediately to your

shipping carrier.

DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER UNTIL

AN APPROPRIATE CLAIM HAS BEEN FILED WITH THE CARRIER AND A

RETURN MATERIAL AUTHORIZATION NUMBER (RMA) HAS BEEN RECEIVED

FROM THE MANUFACTURER.

GETTING STARTED

1. Plug the power cord into a wall receptacle or power strip that will accept

this type of plug.

2. Attach an input/output video cable ( not included ) from the NTSC VIDEO

RCA CONNECTOR or RF-NTSC CONNECTOR TYPE F in the rear

panel of the monitor to a compatible connector on your video equipment.

3. See remote control for specific operation. (page 14)

Should further adjustment or alignment be necessary contact DOTRONIX,

INC. customer service.

INSTALLERS MENU ADJUSTMENTS

To access the Installer's Menu, press and hold the MENU key until the User

Menu display disappears, then press 9876, and then ENTER to access the

Installer's Menu.

1390-04

Microcontroller

Part Number

03HPos9

Build Date

10/04/00

The black bar near the top of the screen indicates the part number of the

software in the display. To the right is a number indicating that the module has

been tested. The date on the black bar near the bottom of the screen indicates

the date the module went through the factory.

When the Installer's menu appears, it displays the third Service Menu item:

POWER MANAGE. Use the Up/ Down Arrow keys to toggle through all of the

adjustments. Use Left/Right Arrows to make a change to the

00 FACT MENU: Use SELECT UP and DOWN Keys to select item 00, the

Factory Mode. This item is used by the Factory when the module is being

tested. It has two positions: 0 and 1. In the field, this item should always be left

off (Zero is off).

When this item is off, only the first twenty-four items in the Installer's Menu can

be accessed. They appear one at a time near the middle left of the screen.

When this item is set to 1, 79 menu items are available.

In the Factory Menu, only the selected menu item is displayed, near the top of

the screen, as shown in the figure above.

When the Factory Menu is on, the AC Power-On feature is always enabled

regardless of the setting of AC ON in the Installer's Menu. The display will

automatically come on when AC is applied.

Use the remote to reenter the Installer's Menu to turn the Factory Menu off. The

Factory Mode may also be turned off by setting the clock, or running the Auto

Program feature in the customer Set Up menu.

01 PRESET PX: Stores the video customer menu adjustments in the nonvola-

tile memory of the EAROM. Selections are Custom and Preset-Store. Settings

for Contrast, Brightness, Color and Tint are stored in this manner. 0 is custom

and 1 is Preset stored.

02 PRESET AX: Stores customer Audio menu adjustments in the nonvolatile

memory of the EAROM. Selections are Custom and Preset-Store. Settings for

Bass, Treble, Balance and SoundRite are stored in this manner. 0 is custom

and 1 is Preset stored.

2.08

Program

Font

Revision

Factory Option

TE Status

TE=10110000