Dahl VARIODOCK Руководство по техническому обслуживанию - Страница 9

Просмотреть онлайн или скачать pdf Руководство по техническому обслуживанию для Док-станция Dahl VARIODOCK. Dahl VARIODOCK 19 страниц.

Печатать страницу

Dahl VARIODOCK Руководство по техническому обслуживанию

Installation of Dahl VarioDock™

Installation must be carried out by a qualified and

manufacturers' instructions for use and assembly,

experienced technician/fitter.

which must be followed when installing the lock

In the area where the wheelchair is to be locked into

plate and spacer.

the docking system, the floor must be flat along the

C. Be aware that bolts with art.no. # 502800 for secur-

full length and width of the wheelchair. The length

ing the lock plate are custom made bolts, which

of the flat floor must be such that it is possible to

are only available in one length. It is very important

manoeuvre the wheelchair into the docking system

that the installer carefully adjusts the bolts to the

without problems. It is essential that there is no dif-

correct length, which fits the individual wheel-

ference in the height of the floor from one side to the

chair's approved adaptation kit with spacers, if

other at the location where the docking station is to

applicable. If the bolts are too short to fully engage

be installed. It is also important that the lock plate is

into the entire thread depth, they will not be strong

fitted straight/horizontally under the wheelchair. If the

enough to withstand the load during a collision. If

above is not carried out carefully, there is a risk that

the bolts are too long, the batteries or other wheel-

the wheelchair may not be manoeuvred properly into

chair components may be damaged. Therefore be

place in the docking station.

careful when shortening the bolts.

1. Delivery of VarioDock

Warning! Never use bolts other than original Dahl

A. VarioDock

is installed on a plate for transport

bolts # 502800 for fixing the lock plate. Standard bolts

when delivered to avoid damage during transport.

are not strong enough to withstand a collision.

Remove this plate and the 6 bolts before installing.

3. Measuring ground clearance

See also instructions 5 and 6 on page 17.

A. For correct determination of the wheelchair's

2. Installing the lock plate

ground clearance, it must be measured with the

A. Install the lock plate and 8 mm spacer under the

user seated in the wheelchair (pay attention to

wheelchair in accordance with the wheelchair man-

correct tyre pressure). Carefully drive the wheel-

ufacturer's instructions, which can be downloaded

chair into the VarioDock

from our website, as well as instructions on the

VarioDock

drawings on pages 5 and 14. Before the lock plate

the underside of the lock plate and docking station.

and spacer are installed, carry out the following:

B. Read the ground clearance off the display and write

B. The installer must make sure that the wheelchair

it on the supplied sticker (see the design of the

has a solid construction at the place where the

sticker on the right).

lock plate shall be installed which can withstand

4. Location of VarioDock™

the load during a collision. On our website http://

A. Place the wheelchair, with the user sitting in it,

wtors.com you can see the list with all approved

facing forward in the vehicle at the desired installa-

adaptation kits for wheelchairs and download

tion location. If the user is the driver of the vehicle,

Maintenance manual, installation and user guide UK

make sure that the user can reach and operate all

necessary instruments and driving functions in a

proper and safe manner from this position.

B. Place the docking station under the wheelchair.

C. Mark the docking station's position on the floor

and the lock plate's position (in width and length)

under the wheelchair.

5. Beginning installation work

Ask the wheelchair user to leave the vehicle, so that

installation work can begin.

A. Drive the VarioDock

to the lowest position

(61mm) before you begin installation work.

B. Loosen the 4 bolts on the side of the VarioDock

(important: note instructions on page 21!) and

carefully remove the top section of the docking sta-

tion. See pictures 3 and 4 on page 17. (Please note

that electronic components are installed in the top

section!). Mark the location of the bolts on the floor

of the vehicle, and drill holes through the floor

at these locations. Be careful when marking and

drilling through the vehicle floor to avoid damage

to brake pipes, wires, fuel tank and the like. Never

drill any holes until you are certain that the holes

Varenr. DIV99L - Labels, matsølv

match the location of the installation components.

and set the height of

C. Secure the docking station with the supplied bolts,

so that there is 2 mm space between

Format:85 x 20 mm, udstanset

nuts, etc. See illustrations pages 18 and 19.

Farver: Sort tryk

Installation of Dahl VarioDock

Removal of top section

Pictures 1-6

1. Loosen bolts, see instructions 3 on page 21

2. Bolts are loosened

3. Carefully remove the top section

4. Place top section as shown on picture

5. Plate and 6 bolts used for transportation

of the VarioDock

, shown on picture 6,

must be dismantled and discarded!

6. The transportation plate and bolts are

now removed

Fitting the top section

Picture 7

When assembling the slide and bottom

frames, the pin of the potentiometer must

be carefully placed in the hole of the bottom

frame, otherwise there is a risk of damaging

the potentiometer. If the docking station is

Drill holes in

tightened when the pin is not inserted in the

the anchorage

hole, the potentiometer will be destroyed/

plate for running

damaged.

through cables, if

necessary.

Dahl VarioDock™