Dovre 500cc Руководство по установке и эксплуатации - Страница 13

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Дровяная печь Dovre 500cc. Dovre 500cc 19 страниц.

Печатать страницу

-11-

J!UJllU~1lSJ

WOOD

FI~

OPEN EITHER THE SIDE OR FRONT LOADING DOORAND THE BYPASS DAMPER CONTROL (TURNED TO IP

POSITION).

BUILD A SMALL FIRE USING PAPER AND DRY KINDLING.

AFTER LIGHTING THE FIRE,

CLOSE THE DOOR AND OPEN THE DRAFT CONTROLS (BOTH FRONT AND SIDE) TO THE FULL-OPEN

POSITON.

ONCE A 1"-2" BED OF COALS HAS BEEN ESTABLISHED, ADD 2 OR 3 MEDIUM SIZE SPLIT LOOS (ABOUT

2"-4"

DIAMETER), KEEPING THE BYPASS DAMPER AND DRAFT INLETS OPEN. NORMALLY AFTER 15

TO 30 MINUTES AND THE CATALYST TEMPERATURE IS 400° TO 500° F, THE CATALYST WILL BE

OPfRATING. THEN Cl.OSE THE BYPASS DAMPER.

TO REDUCE THE AMOUNT OF HEAT PRODUCED BY YOUR UNIT, START BY CLOSING THE SIDE DRAFT

INLET AND THEN ADJUSTING THE FRONT DRAFT CONTROLS. BY CLOSING THE SIDE DRAFT INLET FIRST

AND THEN ADJUSTING THE FRONT DRAFT INLETS, YOU WILL CONTROL THE STOVES HEAT OUTPUT AND

MAINTAIN A DESIRABLE ROOM TEMPERATURE.

FOR MAXIMUM HEAT OUTPUT, OPEN THE FRONT DRAFT CONTROLS COMPLETELY AND THE SIDE DRAFT

CONTROL TO FUll-OPEN

THIS WILL ALLOW THE UNIT TO PRODUCE 30,000

TO 50,000

BTU/HR

WITH SURFACE TEMPERATURES OF 600· TO 900

CAIAlYIIC

PROBE THERMOMETER

(CPT) :

DURING START UP OF YOUR DOVRE HORIZON AND DURING THE REFUELING CYCLES, THE

TEI1PERATURES SHOWN ON YOUR CATALYTIC PROBE THERMOMETER (CPT)WILL TELL YOU HOW YOUR

CATALYST :3 OPERATING AND WHEN THE BYPASS DAMPER MAY BE CLOSED. THE LOCATION OF THE CPT

PROVIDES THE MOST ACCURATE READING, SINCE IT IS DIRECTLY ABOVE THE CATALYTIC COMBUSTOR.

DURING START UP OR REFUELING, THE BYPASS DAMPER IS OPEN. WHEN THE CPT REACHES 400· TO

500

F, THE BYPASS DAMPER MAY BE CLOSED. AT THIS POINT, THE CATALYTIC COMBUSTOR IS HOT

ENOUGH TO FUNCTION.

THE INFORMATION FROM A SURFACE THERMOMETER IS VERY HELPFUL IN ADJUSTING THE DRAFT

INLETS FOR THE DESIRED HEAT OUTPUT. YOU SHOULD REMEMBER THAT THE TEMPERATURES AND AIR

INLET SETTINGS Will

VARY DEPENDING ON THE TYPE OF WOOD, MOISTURE CONTENT OF THE WOOD.

AND THE DRAFT OF YOUR CHIMNEY.

AS YOU BECOME fAMILAR

WITH YOUR UNIT. YOU WILL

DETERMINE THE BEST AMOUNT OF FUEL AND DRAFT SETTING FOR THE HEATING REQUIREMENTS OF

YOUR HOME.

INCIDENTALLY,

DURING THE FIRST FIRING,

YOUR DOVRE UNIT WILL

GIVE OFF A SLIGHTLY

UNPLEASANT DOOR AS THE HIGH TEMPERATURE PAINT CURES. DON'T BE ALARMED, AS THIS WILL

ONLY LAST FOR ABOUT 30 TO 60 MINUTES AFTER THE SURFACE TEMPERATURE ON THE STOVE

REACHES 400°F.

ADDING FUEL;

USE THE ASH HOE PROVIDED WITH YOUR UNIT TO SEPERATE HOT COALS FROM THE ASH. BY PUSHING

THE ASH TO THE REAR OF THE FUEL BED AND PULLING THE HOT COALS FORWARD TOWARD THE AIR

INLET, YOU WILL BE ABLE TO QUICKLY AND EASILY RECHARGE THE FIRE. ADD 2 OR 3 LOOS, CLOSE

THE LOADING DOORAND COMPLETELY OPEN THE DRAFT CONTROL.