DQ HEATING DUNE Руководство пользователя - Страница 3
Просмотреть онлайн или скачать pdf Руководство пользователя для Нагреватель DQ HEATING DUNE. DQ HEATING DUNE 4 страницы.
Печатать страницу
INSTALLATION GUIDE
Installation information in this section
G
includes below products!
E
ARES, NORTE, RAMSEY
D
F
CONTENT OF MOUNTING SET
C
Decorative Cap (x6)
A
Only for mirror finished products
B
A
Wall Mounting
Bracket
D
Air Vent (x1)
G
Installation information in this section
E
includes below products!
BIANCA, UNO, MALIBU
G
CONTENT OF MOUNTING SET
J
Decorative Cap (x1)
Only for mirror finished products
C
A
I
Wall Plug (x12)
E
Screw cap (x12)
I
B
A
Place your radiator at least 12.5 cm above the floor.
Provide insulation by wrapping PTFE tape on the treads before installing the valves.
IMPORTANT NOTE
Apply silicone seal fluid to all treaded parts containing o-rings.
Connect your radiator to the utilities after following all the installation steps in the manual.
After connecting to the utilities, do not forget to discharge the trapped air inside the radiator before commissioning.
SPIRIT LEVEL
ELECTRIC DRILL &
DRILL BIT
INSTALLATION
Wall Mounting
Blind Plug (x5)
Screw (x4)
B
C
C
Wall plug (x4)
Setscrew (x4)
(x4)
1-
E
E
F
by using a metric ruler.
2-
as desired, align with the ground by
Diverter (x1)
using a spirit level and mark the
H G
position of the wall mounting
brackets.
INSTALLATION
Wall Mounting
Blind Plug (x1)
Screw (x12)
B
C
C
Screw Cap
Air Vent (x1)
Holder (x12)
G
E
J
1-
using a metric ruler.
2-
desired, align with the ground by using
a spirit level and mark the position of
the wall mounting brackets.
TOOLS REQUIRED FOR INSTALLATION
&
CORDLESS
&
CROSS POINT
METRIC RULER
HAMMER
SCREWDRIVER
SCREWDRIVER
(BIT PH2)
1
2
2
1
90°
1-
Adjust the height of your radiator
Drill holes (Ø 10 mm) into the spots
you have marked.
2-
Nail the wall plugs (E) in the holes
Set the location of your radiator
by using a hammer.
3-
Screw the wall mounting brackets
all the way to the holes with the help
of a screwdriver.
1
2
1
2
1
90°
1-
Adjust the height of your radiator by
Drill holes (Ø 10 mm) into the spots
you have marked.
2-
Nail the wall plugs (E) in the holes
Set the location of your radiator as
by using a hammer.
STEP LADDER
ALLEN KEY
(FOR HIGH PRODUCTS)
3
2
1
1
2
3
1-
Place your radiator into the wall
mounting brackets (D).
2-
Insert the setscrews (F) into the
slots on the mounting brackets (D),
adjust the distance between the wall
and your radiator then tighten the
setscrews by using an Allen key
(M3).
3
2
2
1
1-
Pass the wall mounting screws (C)
through the screw cap holders (J).
2-
Place your radiator on the wall
and screw the mounting brackets all
the way into the wall with the help of
a screwdriver.
4
1
2
2
1-
Insert the diverter into the tube
where the outlet valve is located
then push until it reaches the metal
sheet inside the tube.
2-
Screw the diverter onto the metal
sheet by using an Allen Key (M10).
4
1
1-
Attach the screw caps (I) to the
screw cap holders (J) on the wall
mounting brackets.