Electrolux # Руководство по эксплуатации - Страница 18

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Холодильник Electrolux #. Electrolux # 49 страниц. Over the range microwave oven
Также для Electrolux #: Руководство по установке (8 страниц), Руководство по эксплуатации и уходу (20 страниц), Руководство по эксплуатации и уходу (36 страниц), Руководство по эксплуатации и уходу (24 страниц), Руководство по эксплуатации и уходу (38 страниц), Книга рецептов (17 страниц), Буклет с инструкциями (12 страниц), Руководство по эксплуатации и уходу (20 страниц), Книга инструкций (16 страниц), Книга инструкций (12 страниц), Руководство по инсрукции (16 страниц), Руководство пользователя (11 страниц), Руководство по эксплуатации и уходу (26 страниц), Руководство по эксплуатации и уходу (38 страниц), Руководство пользователя (9 страниц), Руководство по эксплуатации и уходу (16 страниц), Руководство по эксплуатации и уходу (16 страниц), Руководство по установке (21 страниц), Руководство пользователя (16 страниц), Руководство по эксплуатации и уходу (16 страниц)

Печатать страницу
Electrolux # Руководство по эксплуатации
GLMV169GSB
GLMV169GBB
GLMV169GQB
PLMVZ169GCB/C
PROCEDURE
LETTER
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE,
F
PRIMARY INTERLOCK SWITCH TEST
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO)
terminal of the switch. The meter should indicate an open circuit with the door open and a closed
circuit with the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling
SECONDARY INTERLOCK RELAY (RY2)
. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check
the state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay
contacts are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
TEST PROCEDURES
REPLACE TEMPERATURE FUSE.
fan motor, stirrer motor and oven light will be activated by RY.
COMPONENT TEST
8