Bosch ASCENTA SHX5AL Руководство по эксплуатации и уходу - Страница 19
Просмотреть онлайн или скачать pdf Руководство по эксплуатации и уходу для Посудомоечная машина Bosch ASCENTA SHX5AL. Bosch ASCENTA SHX5AL 26 страниц. Bosch ascenta models dishwashers use & care manual
Также для Bosch ASCENTA SHX5AL: Руководство по эксплуатации и уходу (21 страниц), Руководство по эксплуатации и уходу (21 страниц)
Печатать страницу
Operating the Dishwasher
SHE5AL, SHE4AP
To start the dishwasher:
•
Door must be closed. Press the "ON/OFF" button.
•
One of the Wash Cycle LEDs will be flashing. You can
now select a wash cycle.
•
Press the "<" or ">" button to select the desired wash
cycle.
•
Select the "Half Load" or "Delay Start" features if
desired at this point.
If you would like to delay the start time of the dishwasher
press the "DELAY" button until the desired delay time
(3,6,9 hrs.) is displayed by the corresponding LED.
•
Press the "START" button to begin the cycle (Wash
Cycle Indicator Light will stop flashing)
NOTE: Rinse Agent Indicator Light will be illuminated if
the unit needs Rinse Agent.
Child Lock
•
After pressing the "START" button you can activate
the Child Lock feature.
•
Press and hold down the "<" button until Child Lock
LED illuminates (Light goes out when button is
released).
•
Now any button you press (except ON/OFF) will not
function and the Child Lock LED illuminates when
you press any button.
•
To deactivate, press and hold the "<" button until the
Child Lock LED goes out.
To cancel a cycle:
•
Press and hold the "START/RESET" button until the
"Active" LED goes out.
•
Wait for about 1 minute until the dishwasher drains.
•
The "Clean" indicator light will illuminate when done
draining.
•
Turn unit off by pressing the "ON/OFF" button.
•
You are now ready to start a new cycle.
To enter the options mode(rinse agent setting, ex-
tra dry heat, cycle completion signal):
•
Door must be closed. Press the "ON/OFF" button to
turn the unit on.
•
One of the Wash Cycle LEDs will be flashing.
•
Press and hold down the ">" button, then press and
release the "START/RESET" button. Now release the
">" button.
•
The "Clean" and one other LED will be flashing. You
are now in the options setup mode.
•
Press ">" to select the option you would like to
adjust.
If the "Clean" and "Rinse Agent" LED are flashing you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized" LED are flashing you can set
the Extra Dry Heat.
To set the amount of Rinse Agent:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions to enter "options" mode.
With the
"Clean" and "Rinse Agent" LED
•
Press the "<" button to change the amount of rinse
agent dispensed.
0 LEDs flashing --> Rinse Agent dispenser is OFF
1 LED flashing --> Lowest amount of rinse agent
2 LEDs flashing --> Medium amount dispensed
3 LEDs flashing --> Highest amount of rinse agent
•
Press
START to save your settings.
To turn Extra Dry Heat on or off:
With the
"Clean" and "Sanitized" LED
•
Press the "<" button to turn Extra Dry Heat on or off.
0 LEDs flashing --> Extra Dry Heat is OFF
1 LED flashing --> Extra Dry Heat is ON
•
Press
START to save your settings.
flashing:
flashing:
0
19